Abit KU8 Скачать руководство пользователя страница 43

Страница: 43 / 72

BIOS Setup

3-17

USB Mouse Support Via:

This item allows you to select [

BIOS

] for using USB mouse in DOS environment, or [

] in OS

environment.

OnChip Audio Controller:

This option enables or disables the audio controller.

Super IO Device:

Click <Enter> key to enter its submenu:

Phoenix – AwardBIOS CMOS Setup Utility

SuperIO Device

Onboard FDC Controller

Enabled

Item Help

Onboard Serial Port 1

3F8/IRQ4

Onboard Parallel Port

378/IRQ7

Parallel Port Mode

SPP

X - EPP Mode Select

EPP1.7

X - ECP Mode Use DMA

↑↓

:Move Enter:/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Onboard FDC Controller:

Two options are available: Enabled and Disabled. The default setting is

Enabled

. You can enable or

disable the onboard FDC controller.

Onboard Serial Port 1:

This is used to specify the I/O address and IRQ of Serial Port 1. Six options are available: Disabled

3F8/IRQ4

2F8/IRQ3

3E8/IRQ4

2E8/IRQ3

AUTO. The default setting is

3F8/IRQ4

Onboard Parallel Port:

Sets the I/O address and IRQ of the onboard parallel port. Four options are available: Disabled

378/IRQ7

278/IRQ5

3BC/IRQ7. Default setting is

378/IRQ7

Parallel Port Mode:

Four options are available: SPP

EPP

ECP

ECP+EPP. The default setting is

SPP

mode.

EPP Mode Select:

Two options are available: EPP1.7

EPP1.9. The default setting is

EPP 1.

7 When the mode selected for

the parallel port mode is EPP, the two EPP version options are available.

User’s Manual

Содержание KU8









































































Результаты поиска

Содержание KU8

Отзывы:

Похожие инструкции для KU8

Бренды по названию

Популярные бренды

Abit KU8, Руководство пользователя

Результаты поиска

Содержание KU8

Отзывы:

Похожие инструкции для KU8

Бренды по названию

Популярные бренды