Abit KU8 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 72

background image

2-8

Chapter 2

(4). Front Panel Switches & Indicators Headers

This header is used for connecting switches and LED indicators on the chassis front panel.

Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.

•

HLED (Pin 1, 3):

Connects to the HDD LED cable of chassis front panel.

•

RST (Pin 5, 7):

Connects to the Reset Switch cable of chassis front panel.

•

SPKR (Pin 13, 15, 17, 19):

Connects to the System Speaker cable of chassis.

•

SLED (Pin 2, 4):

Connects to the Suspend LED cable (if there is one) of chassis front panel.

•

PWR (Pin 6, 8):

Connects to the Power Switch cable of chassis front panel.

•

PLED (Pin 16, 18, 20):

Connects to the Power LED cable of chassis front panel.

KU8

«
...
14
15
16
17
18
...
»

Содержание KU8









































































Отзывы:

Нет отзывов

Похожие инструкции для KU8

Бренд: Linear Technology Страницы: 10

Бренд: BCM Страницы: 5

Бренд: BCM Страницы: 3

Track bq27520EVM

Бренд: Texas Instruments Страницы: 22

Бренд: Intel Страницы: 30

Бренд: TransCore Страницы: 40

Бренд: Gigabyte Страницы: 96

Бренд: Avalue Technology Страницы: 29

Бренд: Gigabyte Страницы: 96

Бренд: MSI Страницы: 77

Бренд: Gigabyte Страницы: 2

PN1 SLI2 Extreme

Бренд: ECS Страницы: 62

Бренд: u-blox Страницы: 37

Бренд: MSI Страницы: 76

FM2A75M-DGS R2.0

Бренд: ASROCK Страницы: 59

Бренд: ASROCK Страницы: 190

iPervoice 1039/56

Бренд: urmet domus Страницы: 3

Бренд: Thunder Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды