Abit IS7 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 110

background image

3-8

Chapter 3

First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device:

Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device], and
[Third Boot Device] items respectively. The BIOS will boot the operating system according to the
sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another
device other than these three items.

CPU L3 Cache:

This item is used to enable the L3 cache (default setting), and appears only for certain CPU (Intel Pentium
4 processor with HT Technology Extreme Edition) that possesses L3 cache.

Swap Floppy Drive:

When set to [Enabled], and the system is booting from the floppy drive, the system will boot from drive B
instead of the regular drive A. There must be two floppy drives connected in the system to use this
function.

Boot Up Floppy Seek:

When set to [Enabled], the BIOS will check whether the floppy disk drive is installed or not.

Boot Up NumLock Status:

This item determines the default state of the numeric keypad at system booting up.

[On]:

The numeric keypad functions as number keys.

[Off]:

The numeric keypad functions as arrow keys.

Security Option:

This item determines when the system will prompt for password - every time the system boots or only
when enters the BIOS setup.

[Setup]:

The password is required only when accessing the BIOS Setup.

[System]:

The password is required each time the computer boots up.

NOTE:

Don’t forget your password. If you forget the password, you will have to open the computer case

and clear all information in the CMOS before you can start up the system. But by doing this, you will
have to reset all previously set options.

APIC Mode: (For IS7-G, IS7, IS7-E, and IS7-M only)

Leave this item to its default setting.

MPS Version Ctrl For OS:

This item specifies which version of MPS (Multi-Processor Specification) this motherboard will use.
Leave this item to its default setting.

OS Select For DRAM > 64MB: (For IS7-G, IS7, IS7-E, and IS7-M only)

This item allows you to access the memory that is over 64MB in OS/2. Leave this item to its default
[Non-OS2] setting for operating system other than OS/2.

IS7 Series

«
...
60
61
62
63
64
...
»

Содержание IS7















































































































Отзывы:

Нет отзывов

Похожие инструкции для IS7

Бренд: Zapi Страницы: 50

Бренд: MSI Страницы: 35

Бренд: ASROCK Страницы: 138

Бренд: AOpen Страницы: 96

Бренд: Intel Страницы: 78

Бренд: IBASE Technology Страницы: 93

Бренд: Aaeon Страницы: 37

STEVAL-ISB042V1

Бренд: ST Страницы: 26

SERVER SYSTEM SR2500AL

Бренд: Intel Страницы: 210

Бренд: Aaeon Страницы: 56

Бренд: SOYO Страницы: 94

Бренд: Texas Instruments Страницы: 36

KX224-I2C-EVK-001

Бренд: Rohm Страницы: 3

Бренд: ST Страницы: 11

Бренд: Gigabyte Страницы: 23

SIDE POWER SRH 240 TC

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: Texas Instruments Страницы: 28

TAS5001-5122C2EVM

Бренд: Texas Instruments Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды