Abit AR5 Скачать руководство пользователя страница 54

Страница: 54 / 88

3-26

Chapter 3

On Board FDD Controller:

This is to Enable or Disable the Onboard FDD Controller.

On board Serial Port 1:

This is used to specify the I/O address and IRQ of Serial Port 1. Five
options are available: Disable, 3F8h/IRQ4, 2F8h/IRQ3, 3E8h/IRQ4 or
2E8h/IRQ3.

On board Serial Port 2:

This is used to specify the I/O address and IRQ of Serial Port 2. Five
options are available: Disable, 3F8h/IRQ4, 2F8h/IRQ3, 3E8h/IRQ4 or
2E8h/IRQ3.

Attention:Do not select the same I/O address and IRQ for the two serial

ports, otherwise the serial ports will not be able to operate
normally.

Onboard IR Function:

Onboard serial port 2 can support IR (Infrared) function. Three
options are available:

Disable: No support for IR function.

IrDA (HPSIR) mode.

ASK IR (Amplitude Shift Keyed IR) mode.

IR Duplex Mode:

Set the IR mode as Half or Full. Default is Half.

IR Tr/Re Polarity:

Set IR transmission/reception polarity as High or Low.

On board parallel Port:

Set the I/O address and IRQ of the onboard parallel port. Four options are
available: Disable, 3BCh/IRQ7, 278h/IRQ5 and 378h/IRQ7. Default is
378h/IRQ7.

Parallel Port Mode:

Can be set as EPP v.1.7, EPP v. 1.9, ECP, ECP+EPP 1.7, ECP+EPP
1.9 or Normal (SPP) mode. Default is Normal (SPP) mode.

Содержание AR5

























































































Результаты поиска

Содержание AR5

Отзывы:

Похожие инструкции для AR5

Бренды по названию

Популярные бренды

Abit AR5, Руководство пользователя

Результаты поиска

Содержание AR5

Отзывы:

Похожие инструкции для AR5

Бренды по названию

Популярные бренды