Abit AR5 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 88

background image

Introduction of BIOS

3-13

Boot Up Floppy Seek:

When computer boots up, the BIOS detects if the system has FDD or not.
When this item is enabled, if the BIOS detects no floppy drive, it will display
a floppy disk drive error message. If this item is disabled, the BIOS will skip
this test.

Boot Up NumLock Status:

ä

On: At boot up, the Numeric Keypad is in numeric mode.

ä

Off: At boot up, the Numeric Keypad is in cursor control mode.

IDE HDD Block Mode:

This item can be set as Enable or Disable.

Most of new hard disk drives (IDE drives) support multi-sector transfers.
This feature speeds up hard disk drive access performance and reduces the
time necessary to access data. When this item is enabled, the BIOS will
automatically detect if your hard disk drive supports this feature or not, and
will choose the right settings for you.

2

For further details about hard disk drive installation, refer to appendix E.

Typematic Rate Setting:

This item allows you to adjust the keystroke repeat rate. When enabled, you
can set the two keyboard typematic control that follow (Typematic Rate and
Typematic Rate Delay). If this item is disabled, the BIOS will use the default
setting.

Typematic Rate (Chars/Sec):

When you press a key continuously, the keyboard will repeat the keystroke
according to the rate you have set. (Unit: characters/second

¡^

Typematic Rate Delay (Msec):

When you press a key continuously, if you exceed the delay you have set
here, the keyboard will automatically repeat the keystroke according a
certain rate. (Unit: milliseconds)

«
...
39
40
41
42
43
...
»

Содержание AR5

























































































Отзывы:

Нет отзывов

Похожие инструкции для AR5

Бренд: Yamaha Страницы: 20

Side-Power SEP IP Series

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: JETWAY Страницы: 37

MEG X570S UNIFY-X MAX

Бренд: MSI Страницы: 204

AR0832MBSC25SUFAH-GEVB

Бренд: ON Semiconductor Страницы: 6

Бренд: IWILL Страницы: 48

Бренд: ASROCK Страницы: 2

Бренд: IEI Technology Страницы: 145

Бренд: Silicon Laboratories Страницы: 9

Бренд: JETWAY Страницы: 46

Бренд: ST Страницы: 11

Бренд: ASROCK Страницы: 2

Бренд: unicore Страницы: 11

Бренд: Biostar Страницы: 84

Бренд: Analog Devices Страницы: 4

Бренд: Silica Страницы: 23

Бренд: Megatel Страницы: 86

Бренд: Asus Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды