background image

decomposed 3M™ Novec™ 5110 (an example 
can be found in instruction manual 
1YHA000300 en) is displayed in the 
switchgear room.

- For SF

6

 application:  A work instruction for 

handling of SF

6

 (an example can be found in 

instruction manual 1YHA000333) is displayed 
in the switchgear room.

- The operators have been instructed in the 

theory and practice of operation of the 
switchgear and are familiar with all details of 
operation.

3.2 Energizing the system

Please consult section 4 for procedures for 

operating the devices. Also observe section 3.1.

Switch all circuit breakers off.

Switch all three-position disconnector off.

Switch all three-position disconnector off.

Connecting the incoming feeder panels

Switch the three position disconnector in the 

incoming feeder panel to the “Disconnector 
ON” position.

Switch the circuit breaker in the incoming 

feeder panel “ON”.

The busbar is then at operating voltage.

Before connecting further incoming feeder 
panels, ensure that the phase angle of 
the panels is identical (section 5.2).

Connecting the outgoing feeder panels (loads) 
when these are circuit breaker panels

Switch the three position disconnector in the 

outgoing feeder panel to the “Disconnector 
ON” position.

Switch the circuit breaker in the outgoing 

feeder panel “ON”.

The loads are then switched on.

C O M M I S S I O N I N G

47

3.  Commissioning

3.1 Conditions for commissioning of the switchgear

The conditions for commissioning of the 
switchgear are as follows:

Supply voltage is available.

There are no active Insulating gas pressure alarms.

Visual examination and sample checks on 

installation in accordance with this document 
have been performed.

External control cables and wiring have been 

installed.

Testing of the specified protection data of the 

secondary equipment has been successfully 
performed.

Protection testing has been passed.

Testing of all mechanical and electrical functions 

of the switching devices and corresponding 
operating mechanism has been successfully 
performed.

Testing of the panel and switchgear interlocks 

has been successfully performed.

Several trial switching operations (without 

service voltage) on all switching devices have 
been successfully performed.

Switch positions are correctly displayed on the 

panels and – if necessary – in the control room.

If remote control systems are fitted, these have 

been successfully tested.

Unused outer cones have been closed off and 

insulated.

High-voltage testing has been successfully 

completed.

The high-voltage cables have been installed 

(after high-voltage testing of the busbar).

All cladding and covers have been fitted.

The following accessories have been handed 

over to the operators.
- This manual.
- The corresponding documents and order 

documents.

- Double bit key or barrel lock key for opening and 

closing of the low voltage compartment door.

- Levers and cranks for operation of the operating 

mechanisms (see list of accessories).

- Earthing set (optional).
- Plug-in indicator unit for capacitive 

indication – if necessary (see section 5.1).

- Phase comparator in the case of more than 

one incoming feeder (optional).

- For AirPlus application: A work instruction for 

handling of AirPlus (3M™ Novec™  5110  and 

Содержание ZX0













































































Отзывы: