background image

Symbol

Risk type
PE

Sign that means that you must read the manual before

you install the EVSE

Waste from electrical and electronic equipment

Note: It is possible that not all symbols are present on the EVSE.

2.9

Discard the EVSE or parts of the EVSE

Incorrect waste handling can have a negative effect on the environment and human

health due to potential hazardous substances. With the correct disposal of this

product, you contribute to reuse and recycling of materials and protection of the

environment.

Obey the local rules to discard parts, packaging material or the EVSE.

Discard electrical and electronic equipment separately in compliance with the

WEEE - 2012/19/EU Directive on waste of electrical and electronic equipment.

As the symbol of the crossed out wheeled-bin on your EVSE indicates, do not

mix or dispose the EVSE with your household waste, at the end of use. Instead,

hand the EVSE over to your local community waste collection point for recycling.

For more information, contact the Government Waste-Disposal department in

your country.

2.10

Cyber security

Note: This topic is valid for a wired Ethernet connection.

This product is designed to be connected to and to communicate information and

data via a network interface. It is the Owner's sole responsibility to provide and

continuously ensure a secure connection between the product and Owner's network

or any other network (as the case may be).

The Owner shall establish and maintain any appropriate measures (such as but not

limited to the installation of firewalls, application of authentication measures,

encryption of data, installation of anti-virus programs, etc) to protect the product,

the network, its system and the interface against any kind of security breaches,

unauthorized access, interference, intrusion, leakage and/or theft of data or

information.

Safety

9AKK107992A3069-EN | 004

17

Содержание Terra HP Generation 3 UL





































































































Отзывы: