background image

ABB i-bus

®

 KNX 

Device technology 
 

 

SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A   11 

2.1.4 

Operating and display elements 

Indicator 

Description 

Function 

LED status 
(green/red) 

 

Two-colored indicator for displaying mains 
voltage, overload and short-circuit. For 
SV/S 30.640.3.1, overload and short-circuit 
current values apply to the total current, 
I = I

1

 + I

2

 

Green: 

Device operating normally (I < I

Ovl

)  

Red: 

Overload (I

Ovl

 < I < I

Sc

Red, flashing:  Current limiting is active 

 

Output voltage regulated downwards  

 

(I = I

Sc

OFF: 

Mains voltage absent 

 
 

2.1.5 

Mounting and installation 

Accessibility to the device for the purpose of operation, testing, visual inspection, maintenance and repair 
must be provided compliant to VDE 0100-520. 

Mounting 

Mounting and commissioning may only be carried out by electrical specialists. The appropriate standards, 
directives, regulations and specifications should be observed when planning and setting up electrical 
installations.  

Protect the device from moisture, dirt and damage during transport, storage and operation. 

Only operate the device within the specified technical data! 

The device should only be operated in an enclosed housing (distribution board)! 

Cleaning 

If devices become dirty, they can be cleaned using a dry cloth. Should a dry cloth not remove the dirt, they 
can be cleaned using a slightly moistened cloth and soap solution. Corrosive agents or solutions should 
never be used. 

Maintenance 

The device is maintenance-free. No repairs should be carried out by unauthorized personnel if damage 
occurs, e.g. during transport and/or storage. The warranty expires if the device is opened. 

 
 

Содержание SU/S 30.640.1





































Отзывы: