ABB Sentry BSR23 Скачать руководство пользователя страница 24

Страница: 24 / 32

2TLC010062M0201 Rev.F

Note!

BSR23 is supplied with power through its signal input port R.

Relay output specification

Relay output configuration

4 NO + 1 NC

Maximum operating switching voltage

Note

250 VAC

Overvoltage category

Rated impulse withstand voltage

4 kV

Rated operational voltage

250 VAC

Minimum operating contact load

5 VDC / 10 mA (15 VDC / 3 mA)

Maximum operating switching frequency

0.5 Hz

Rated isolation voltage

400 V

Note!

In a 400 V system a 3 phase load shall only be used in a star connection.

NO contact

AC load (AC15, AC1)

Rated operating voltage (Ue)

250 VAC

Rated operating current (Ie)

1 contact

2 contacts

3 contacts

4.6A

4 contacts

DC load (DC13, DC1)

Rated operating voltage (Ue)

+24 VDC

Rated operating current (Ie)

1 contact

2 contacts

5.6A

3 contacts

4.6A

4 contacts

Required fuse

6.3 A gG, >=1 kA short circuit protection (6 A according to
UL248)

NC contact

AC load (AC15, AC1)

Rated operational voltage (Ue) 250 VAC

Rated operational current (Ie) 0.5A

DC load (DC13, DC1)

Rated operational voltage (Ue) +24 VDC

Rated operational current (Ie) 2A

Required fuse

4 A gG (4 A according to UL 248)

Safety device interface specification

Input (I) R1 and R2

Maximum operating input voltage

27.6 VDC

Minimum input high voltage (VIH

min

)

Note 1

19.2 VDC

Maximum input low voltage (VIL

max

)

Note 2

2 VDC

Typical input impedance

1.5 kΩ

Maximum current sink (I

sink

)

70 mA

Note 1

: Voltage level above VIH

min

is interpreted as logic “1”, in worst case operating

conditions.

Note 2

: Voltage level below VIL

max

is interpreted as logic “0”, in worst case operating

conditions.

Test/start/reset interface specification

Input (I) X1/X2

Содержание Sentry BSR23

































Результаты поиска

Содержание Sentry BSR23

Отзывы:

Похожие инструкции для Sentry BSR23

Бренды по названию

Популярные бренды

ABB Sentry BSR23, Руководство по эксплуатации продукта

Результаты поиска

Содержание Sentry BSR23

Отзывы:

Похожие инструкции для Sentry BSR23

Бренды по названию

Популярные бренды