ABB RELION REX640 Скачать руководство пользователя страница 70

Страница: 70 / 108

5.3

Connecting protective earthing

5.3.1

Connecting protective earthing to relay

Connect the protection relay to earth using a 6 mm

(AWG 10) flat braided copper

cable. Use an earth lead of maximum 1.5 m (4.9 ft). Extra length is required for door

mounting.

A 16 mm

(AWG 6) flat braided copper cable is recommended for more

demanding EMI environments, such as installations where the relay is

mounted inside a gas insulated switchgear.

1. Using a TX30 screwdriver, loosen the protective earth screw to connect a

separate earth protection lead.

Figure 62: Location of the protective earth pin

Each protection relay must have its own earth lead connected to the

earth circuit connector.

2. Connect the earth lead to the earth bar.
3. Thread the copper cable on the protective earth.
4. Tighten the protective earth screw to 6 Nm ±5% (4.4254 ft-lb ±5%).
5. Support the earth lead so that it cannot break or weaken.

Observe the mechanical, chemical or electrochemical conditions.

Connecting

1MRS759115 E

REX640

Installation Manual

Содержание RELION REX640












































































































Результаты поиска

Содержание RELION REX640

Отзывы:

Бренды по названию

Популярные бренды

ABB RELION REX640, Руководство по установке

Результаты поиска

Содержание RELION REX640

Отзывы:

Бренды по названию

Популярные бренды