ABB +Q951 Скачать руководство пользователя страница 47

Страница: 47 / 56

Fault tracing

Contents of this chapter

This chapter provides general diagnostics and troubleshooting tips.

General

If you cannot reset the emergency stop function with the emergency stop reset button [S62],
check the reset circuit connections. Refer to the circuit diagrams delivered with the drive.

Use a multimeter to measure the STO circuit connections, if the inverter unit generates one
or more of these faults:

• STO hardware failure (5090)

• Safe torque off 1 loss (FA81)

• Safe torque off 2 loss (FA82)

For more information, see the hardware and firmware manuals.

Emergency stop safety relay

￭

ACS880-07CLC drives with Q951+Q984

The type of the emergency stop safety relay [A640] is Phoenix Contact PSR-MC34.

This table gives the indications of the Phoenix Contact PSR-MC34 relay:

State

K2 LED

K1 LED

IN1/2 LED

PWR LED

All relays are not activated. The sensor circuit is off.
Possible error, see the data sheet of the relay.

OFF

The sensor circuit is active. Relays K1 and K2 are
ready to start and await reset/start command.

OFF

Fault tracing 47

Содержание +Q951
























































Результаты поиска

Содержание +Q951

Отзывы:

ABB +Q951, Руководство пользователя, Страница: 47 / 56

Результаты поиска

Содержание +Q951

Отзывы: