ABB +Q951 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 56

ABB +Q951 Скачать руководство пользователя страница 36

￭

ACS880 multidrives

The parameter settings in the ACS880 primary control program:

Description

Default value

1)

Name

No.

Selects a drive signal to be connected to relay output RO1.
In this case, the source is the inverted value of parameter

10.01 DI status

bit 3 (DI4).

P.10.1.3 -

2)

RO1 source

10.24

Selects the way the motor is stopped when an emergency
stop command is received.

Eme ramp stop (Off3)

Emergency
stop mode

21.04

Selects the source of the emergency stop signal.

DI4

2)

Emergency
stop source

21.05

1) Value set by ABB at the factory for the default design.
2) Delivery-specific. Refer to the circuit diagrams.

The table that follows gives the parameters in the ACS880 primary control program that you
must set according to application requirements. Make sure that the selected values agree
with the time delay settings of the emergency stop safety relay [A61]. Refer to

settings (page 37)

Description

Value

Name

No.

Defines the zero speed limit. The motor is stopped along a
speed ramp until this limit is reached. After the zero speed
delay (parameter

21.07

, default value

0 ms

), the motor coasts

to a stop.

User-defined

Zero speed lim-
it

21.06

Defines the deceleration time for emergency stop Off3. The
deceleration time is the time it takes to decelerate the motor
from the maximum process speed defined by parameter

46.01

or

46.02

to the zero speed limit defined by parameter

21.06

.

User-defined

Emergency
stop time

23.23

Defines the maximum motor speed used in the application.
Set this parameter if you use the speed control mode or
torque control mode.

User-defined

Speed scaling

46.01

Defines the maximum motor frequency used in the applica-
tion. Set this parameter if you use the frequency control
mode.

User-defined

Frequency
scaling

46.02

The table that follows gives the parameters related to the safety function in the ACS880
supply control programs. The parameters are set at the factory.

Description

Default value

1)

Name

No.

Selects the way the supply unit is stopped when an emer-
gency stop command is received.

Stop and warning

Emergency
stop mode

121.04

Selects the source of the emergency stop signal. This para-
meter cannot be changed while the supply unit is running.

DIIL

Emergency
stop source

121.05

1) Value set by ABB at the factory for the default design.

For more information, see the firmware manuals.

36 Description of Q952+Q984

«
...
34
35
36
37
38
...
»

Содержание +Q951

























































Отзывы:

Нет отзывов