ABB Power2 800-M Скачать руководство пользователя страница 5

Страница: 5 / 24

Assembly Instructions / Power2 800-M

Introduction

Page 3 / 21

HZTL455311P0010

Revision -

March 2016

Design variants

This document is valid for different design variants of low and high-pressure stages. There

may be sections and descriptions of components that are not relevant for a specific low or

high-pressure stage.

ABB Turbocharging Service Stations will be happy to provide information about questions re-

garding a design variant (see "Contact Information" on our website

www.abb.com/turbocharging).

Accuracy of illustrations

The illustrations in this document are general in nature and intended for ease of understand-

ing. Differences in detail are therefore possible.

ABB Turbo Systems

ABB Turbo Systems Ltd is identified as ABB Turbo Systems in this document.

Official service stations of ABB Turbo Systems

Official service stations are identified in this document as ABB Turbocharging Service Sta-

tions. They are regularly audited and certified by ABB Turbo Systems. See "Contact Infor-

mation" on our website at www.abb.com/turbocharging.

Definition of pictograms

The following pictograms can occur in this document. These point out actions that must be

taken in accordance with the meaning of the relevant pictogram.

Pictogram Meaning

Tighten with specified torque

Oil free, grease free and dry

Tighten over specified tightening

angle

Affix

Hand-tight, tighten without tools

Measure

Oil

Note

Apply screw locking paste (e.g.

Loctite)

Visually inspect

Apply high-temperature grease

See document

Apply other paste in accordance

with specifications

Dispose of in an environmentally

compatible, professional way and

in compliance with locally applica-

ble regulations.

Table 1: Definition of pictograms

Содержание Power2 800-M

























Результаты поиска

Содержание Power2 800-M

Отзывы:

Бренды по названию

Популярные бренды

ABB Power2 800-M, Оригинальная инструкция по сборке

Результаты поиска

Содержание Power2 800-M

Отзывы:

Бренды по названию

Популярные бренды