ABB Power2 800-M Скачать руководство пользователя страница 22

Страница: 22 / 24

Assembly Instructions / Power2 800-M

Further information

Page 20 / 21

HZTL455311P0010

Revision -

March 2016

Further information

The Operation Manual must be observed with regard to commissioning, operation, mainte-

nance and ordering spare parts.

NOTICE

Operation Manual
The Operation Manual for the low-pressure and high-pressure stage with the

relevant serial number is available online on our website

www.abb.com/turbocharging.

Low-pressure stage

Figure 12: Serial number of low-pressure stage on rating plate

High-pressure stage

Figure 13: Serial number of high-pressure stage on rating plate

One rating plate each is attached on the left and the right side of the foot (bearing casing) and

to the air suction branch of the high-pressure stage.

1. Read the serial number (02) on the rating plate (01) of the low-pressure and high-pressure

stage.

Содержание Power2 800-M

























Результаты поиска

Содержание Power2 800-M

Отзывы:

Бренды по названию

Популярные бренды

ABB Power2 800-M, Оригинальная инструкция по сборке

Результаты поиска

Содержание Power2 800-M

Отзывы:

Бренды по названию

Популярные бренды