ABB OmniCore V250XT страница 74 Скачать руководство пользователя

Страница: 74 / 456

3.5.3 Connecting the manipulator to the controller

General

Connect the manipulator and the controller to each other after installing them. The
lists below specify which cables to be used in each application.

All connectors on the controller are shown in section

Connectors on the OmniCore

V250XT controller on page 65

CAUTION

Verify that the robot serial number is according to the number(s) in the

Declaration

of Incorporation

(DoI).

Main cable categories

All cables between the manipulator and the controller are divided into the following
categories:

Description

Cable category

Handles power supply to and control of the
manipulator's motors as well as feedback
from the serial measurement board.

Manipulator cable

Handles supply to and feedback from any
position switches.

Position switch cables (option)

Handles communication with equipment fitted
on the manipulator by the customer.

Customer cables (option)

Handles power supply to and control of the
external axes motors as well as feedback
from the servo system.

Additional axes cables (option)

These categories above are divided into sub-categories which are specified in
spare part manual. See

Manipulator cables on page 447

Connecting the cables from the manipulator to the controller

Action

Connect the manipulator cable to the connector X1.

Lock the connector with the lever.

Secure the cables to avoid tripping or wear.

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

3 Installation and commissioning

3.5.3 Connecting the manipulator to the controller

Содержание OmniCore V250XT








































































































































































































































































































































































































































































Результаты поиска

Содержание OmniCore V250XT

Отзывы:

Похожие инструкции для OmniCore V250XT

Бренды по названию

Популярные бренды

ABB OmniCore V250XT, Руководство по эксплуатации продукта

Результаты поиска

Содержание OmniCore V250XT

Отзывы:

Похожие инструкции для OmniCore V250XT

Бренды по названию

Популярные бренды