manualshive.com logo in svg

ABB MRP31.0, Техническое описание

Поделиться
Скачать
ABB MRP31.0 Скачать руководство пользователя страница 14

- 14 -

MRP31.0 Technical description

 Issue: 09.2014

Modbus Interface Diagnosis

Diagnosis information is locally displayed using LEDs located on the front side of the Modbus interface.

LED Bus (red, green)

LED DD (red, green)

Meaning

Off

Off

Power Supply missing

Green fl ashing

- Connection to master missing

- Bus address of UMC different form the one confi gured in the master

- I/O size mismatch between device and master

Red fl ashing

Parameter mismatch between device and master

Red

Communication lost, supervision timeout time exceeded

Green

OK, normal data exchange

Amber fl ashing

Amber fl ashing

Initializing

Green fl ashing

Waiting for communication from UMC

Green

OK, normal data exchange

Red fl ashing

Connection to UMC lost

Red

Internal fault. Replace communication interface.

Modbus exception codes

Code

Name

Meaning

01

ILLEGAL FUNCTION

The function code received in the request is not an allowable action for the slave. It could also indicate 

that the slave is in the wrong state to process a request of this type, for example because it is not confi  

gured

02

ILLEGAL DATA ADDRESS

The data address received in the request is not an allowable address for the slave.

03

ILLEGAL DATA VALUE

A value contained in the request data fi eld is not an allowable value for slave. This indicates a fault in the 

structure of the remainder of a complex request, such as that the implied length is incorrect.

04

SLAVE DEVICE FAILURE

An unrecoverable error occurred while the slave was attempting to perform the requested action.

- Wrong confi guration

- Not supported baud rate

- Serial device connected, but parallel device addressed

- Parallel device connected, but serial device addressed

- Connected serial device defective

Содержание MRP31.0

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды