manualshive.com logo in svg

ABB KM26, Руководство по эксплуатации

Поделиться
Скачать
ABB KM26 Скачать руководство пользователя страница 7

7

KM26 | 

MAGNETIC LEVEL GAUGE  |  OI/KM26-EN REV I

Certifications nameplates

The MLG is identified by the name plates. The nameplate 
provides information (refer to figures 2 and 3) concerning the 
model number, pressure ratings, serial number, temperature 
limits etc. The certification plate contains the certification-
related parameters for use in a hazardous area. 
Please refer to the serial number when speaking to ABB 
service department personnel.

 . . . 2     Safety

refer to the respective datasheets of the transmitters, 
switches and accessories to have the details of the IP 
protection of such devices associated with the MLG system.

Grounding / earthing

The end user is responsible for grounding the KM26S or 
KM26T level gauge chamber and any ancillary equipment 
attached to these gauges. The end user is to provide a 
grounding / earthing connection acceptable to local and 
national electrical standards. Recommended locations for 
pipe clamp ground or pipe strap ground are the main 
chamber, the bottom or lower chamber branch connection 
locations. For the KM26S, it is also acceptable to connect a 
wire ring terminal to a flange stud locked in with another nut. 
The grounding connection must be metal to metal so any 
paint must be sanded off. Refer to figure 4 for possible 
grounding locations.

Example grounding hardware is depicted below.

Figure 3 - ATEX only nameplate

Figure 4 - Ground hardware

Figure 2 - ATEX and PED nameplate

Note

The name plates shown here are only examples. The name 
plates attached to the device shall contain the information 
per the order.
 

IP protection and designation

The KM26 MLG is certified as conforming to protection type 
IP68 (according to IEC 60529). The first number indicates the 
type of protection the scale assembly has against the entry of 
foreign bodies, including dust. ‘6’ means that it is dust-proof 
(no ingress of dust). The second number indicates the type of 
protection the device has against the entry of water. Please 

A protective grounding connection is absolutely necessary 
to ensure personnel protection, to protect against surge 
(in case of installation of this option) and to prevent 
explosions in potentially explosive environments.

WARNING

Содержание KM26





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды