ABB HT608455 Скачать руководство пользователя

Страница: 40 / 148

Operation Manual / A170-M.. - A175-M..

4 Commissioning / 4.1 Oil supply

HZTL4033_EN

Rev.I

November 2021

Commissioning

4.1

Oil supply

4.1.1

Introduction

In all operating states, a functioning and carefully executed oil supply is an important pre-
requisite for trouble-free operation of the turbocharger.

The lubrication of the turbocharger is usually carried out with oil from the engine oil circula-
tion.

Comply with the enginebuilder's specifications regarding the selection of lubricating oil
and the oil change intervals.

For more information on the oil supply, refer to Chapter

Oil pressure, oil temperature

→

4.1.2

Pre-lubrication and post-lubrication

The pre-lubrication time is at least 2 minutes.

The post-lubrication time is 10 minutes.

If the engine is operated in idle mode 10 minutes before stopping, no additional post-lubric-
ation is required.

4.1.3

Oil filtering

Filtering of the lubricating oil with a filter mesh width of

≤

0.050 mm

is sufficient for the tur-

bocharger.

4.1.4

Oil pressure

Comply precisely with the oil pressure before the turbocharger for trouble-free operation.

Page

146

Содержание HT608455



















































































































































Результаты поиска

Содержание HT608455

Отзывы:

Похожие инструкции для HT608455

Бренды по названию

Популярные бренды

ABB HT608455, Руководство по эксплуатации

Результаты поиска

Содержание HT608455

Отзывы:

Похожие инструкции для HT608455

Бренды по названию

Популярные бренды