ABB HT596619 Скачать руководство пользователя

Страница: 96 / 124

Operation Manual / 4 Product description / A130-H.. - A140-H

8 Dismantling and fitting / 8.6 Removing the compressor casing

HZTL4030_EN

Rev.F

February 2020

8.6

Removing the compressor casing

Mark the casing position for assembly.

Fig. 33: Removing the compressor casing

*) In some installations a special graphite cord sealing (42126) is fitted (see also chapter

Spare parts

→

1. Loosen screws (72011) and remove together with fastening strips (72012).

2. Attach swivel lifting eye (S) to the compressor casing and the lifting gear.

3. Remove the compressor casing (72000) and turn it 180°.

4. Remove and dispose of the O-ring (42012) or graphite cord sealing (42126).

5. Loosen screws (79041) and remove from the compressor casing (72000) with fixing

discs (79040) and diffuser (79000).

If the compressor casing cannot be loosened, it can be pressed off against the turbine cas-
ing using the press-off tool (90042) (see chapter

Pressing off the casing

→

Page

Содержание HT596619





























































































































Результаты поиска

Содержание HT596619

Отзывы:

Похожие инструкции для HT596619

Бренды по названию

Популярные бренды

ABB HT596619, Руководство по эксплуатации

Результаты поиска

Содержание HT596619

Отзывы:

Похожие инструкции для HT596619

Бренды по названию

Популярные бренды