ABB HT596619 Скачать руководство пользователя

Страница: 52 / 124

Operation Manual / 4 Product description / A130-H.. - A140-H

3 Commissioning / 3.2 Inspection procedures

HZTL4030_EN

Rev.F

February 2020

3.2

Inspection procedures

3.2.1

Introduction

Inspection procedures include preventative visual controls, monitoring and measuring work
before and during commissioning. Inspection procedures enable changes to the turbochar-
ger to be detected. Machine damage can be prevented.

3.2.2

Checks before commissioning

Filter mat (if available)

Check for damage and contamination.

Lubricating system

CAUTION

Contaminated oil

Serious damage to engine or property can be caused by dirt and solid ma-
terial particles in the oil.

For the initial commissioning phase and after all service work, flush the
complete lubricating system with warm oil.

Use special running-in filters when running in the engine and after all ser-
vice work on the lubricating system.

Check that the oil filter is clean before commissioning.

Check the oil pressure in the oil supply pipes.

Warning plates

Check whether warning plates are present and legible.

Check whether the protective sheets have been removed from new warning plates.

Version with compressor wheel cooling

CAUTION

Failure of compressor wheel cooling

Any prolonged failure of the compressor wheel cooling will shorten the re-
placement interval of the compressor wheel.

Make sure there is an uninterrupted supply of cooling air during opera-
tion.

Check whether the compressor wheel cooling is fitted on the bearing casing.

Page

Содержание HT596619





























































































































Результаты поиска

Содержание HT596619

Отзывы:

Похожие инструкции для HT596619

Бренды по названию

Популярные бренды

ABB HT596619, Руководство по эксплуатации

Результаты поиска

Содержание HT596619

Отзывы:

Похожие инструкции для HT596619

Бренды по названию

Популярные бренды