ABB HT595115 Скачать руководство пользователя

Страница: 61 / 124

Operation Manual / 4 Product description / A130-H.. - A140-H

5 Operation and service / 5.1 Noise emission

HZTL4030_EN

Rev.F

February 2020

Operation and service

5.1

Noise emission

WARNING

Noise hazards

Exposure to noise can harm the hearing system, impair health and the psy-
chological state and may lead to lack of attention and irritation.

When the engine is running, always wear ear protection.

Always wear ear protection if the sound pressure level exceeds 85 dB(A).

Wear ear protection.

The emission sound pressure level (A-weighted) is measured at a distance of 1 meter from
the turbocharger.

The highest value of the emission sound pressure level

reaches a maximum of 105 dB(A)

near the air inlet. The following prerequisites must be fulfilled with regard to the turbochar-
ger to observe this limit value:

Air-inlet system has been fitted

All standard, noise-reducing measures

have been fitted

Bellows at the air outlet has been acoustically insulated by the enginebuilder

(see Fig. 20:

Noise insulation, bellows

→

32)

The enginebuilder is responsible for insulating the charge air/scavenging air line and the
charge air cooler.

Directive 2006/42/EC, 1.7.4.2 / u / Paragraphs 5 + 7 :
A-weighted emission sound pressure level

The enginebuilder must provide acoustically equivalent measures in case of deviating in-
sulation versions

Page

Содержание HT595115





























































































































Результаты поиска

Содержание HT595115

Отзывы:

Похожие инструкции для HT595115

Бренды по названию

Популярные бренды

ABB HT595115, Руководство по эксплуатации

Результаты поиска

Содержание HT595115

Отзывы:

Похожие инструкции для HT595115

Бренды по названию

Популярные бренды