ABB HART HHT 275 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 15

ABB HART HHT 275 Скачать руководство пользователя страница 11

"Settings" menu

42/18-75 EN

"Settings" menu

11

6 Go pulse dn
Edit the go pulse down.

7 Offset

up

Edit the up offset.

8 Offset

down

Edit the down offset.

9 ADC

noise

Edit the noise band.

2 Auto

configuration

1 Auto

conf

modes

With this menu item you can select the desired auto-configuration mode. Options:
- Complete auto-configuration
- Control parameters only
- Valve range only
- Zero only

2 Auto

conf

locked

With this option you can disable auto-configuration. Press

to activate (ON) or

deactivate (OFF) the lock.

3 Start

auto

conf

Press

to select this option. The message "Initialized" appears in the display,

unless auto-configuration has been locked. Press

(OK) to confirm and start

the auto-configuration function. The message "Auto configuration is running" is
seen in the display. After successful completion the message "Auto configuration
done" appears. You can either press

(OK) to save the data in the TZID-C/

TZID-C200’s non-volatile memory, or press

(ABORT) to reject the data. Note

that a running auto-configuration can be stopped at any time by pressing

(ABORT).

3 Options

1 Analg

pos

feedback

1 Output

min

Enter the current for 0 % stroke (travel). The current is entered as a percentage of
the 4...20 mA range (= 16 mA) , plus 4 mA offset.

Example:

100% = 20 mA (16 mA range + 4 mA offset)
0% = 4 mA (0 mA range + 4 mA offset)
10% = 5.6 mA (1.6 mA range + 4 mA offset)

2 Output

max

Enter the current for 100% stroke (travel). The current is entered as a percentage
(see item 1).

3 Output

action

Select the output action for the module for "analog position feedback".

4 Alarm

messages

Select the alarm current for alarm reporting of the module for "analog position
feedback". Options: "> 20 mA" or "< 4 mA"

F2

F4

F4

F3

F3

«
...
9
10
11
12
13
...
»

Содержание HART HHT 275
















Отзывы:

Нет отзывов