ABB EasyLine EL3020 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 136

background image

Preparation for Installation

17

Requirements for the Installation Site, Power Supply

NOTE
For the analyzers ZO23 and Fidas24 the information contained in the
sections "ZO23: Preparation for Installation" or "Fidas24: Preparation for
Installation (see page 29)" must be considered in addition.

Requirements for the installation site

The gas analyzer is only intended for installation indoors.

The max. altitude of the installation site may not exceed 2000 m above
sea level.

The installation site must be stable enough to bear the weight of the gas
analyzer!
To ensure safe installation and removal, we recommend that the 19-inch
housing is supported in a cabinet or rack with slide rails!

Short gas paths

Install the gas analyzer as close as possible to the sampling location.

Install the gas conditioning and calibration modules as close as possible
to the gas analyzer.

Adequate air circulation

Provide for adequate natural air circulation around the gas analyzer.
Avoid heat build-up.

Mount (see page 68) several 19-inch housings with a minimum spacing of
1 height unit between housings.

Protection from adverse conditions

Protect the gas analyzer from:



Cold



Exposure to heat from e.g. the sun, furnaces, boilers



Temperature

variations



Strong

air

currents



Accumulation of dust and ingress of dust



Corrosive

atmospheres



Vibrations

«
...
15
16
17
18
19
...
»

Содержание EasyLine EL3020









































































































































Отзывы:

Нет отзывов

Похожие инструкции для EasyLine EL3020

Бренд: Waltron Страницы: 11

Бренд: Labom Страницы: 6

Бренд: Labom Страницы: 5

Бренд: Kawai Страницы: 22

Concert Performer CP3

Бренд: Kawai Страницы: 40

Бренд: Kawai Страницы: 36

Бренд: Kawai Страницы: 148

Бренд: Kawai Страницы: 30

Classic Series CS6

Бренд: Kawai Страницы: 96

Бренд: Katronic Страницы: 3

FLUXUS ADM 6725

Бренд: Katronic Technologies Страницы: 148

Бренд: Kawai Страницы: 176

Бренд: WalkLAB Страницы: 16

Бренд: Vaisala Страницы: 90

Бренд: Vaisala Страницы: 4

Бренд: OBDPROG Страницы: 8

Бренд: DGH Страницы: 87

Бренд: Yamaha Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды