ABB EasyLine EL3020 Скачать руководство пользователя страница 124

Страница: 124 / 136

124

EasyLine EL3000 Series Commissioning Instructions

Status Messages

No. Status Message

Reaction/Troubleshooting

110 A S a The instrument is booting.

116 A S a The Profibus module is installed in the

wrong slot! The interface is therefore not
operative. Please install the Profibus
module in slot X20/X21.

Install the Profibus module in slot X20/X21.

119 A S iQ The configuration could not be loaded!

This instrument is therefore currently not
configured. Please load a configuration
using TCT.

This instrument is therefore currently not
configured. Notify service if this occurs
again.

120 F a The maintenance switch is ON.

121 aL The limit value has alarm status.

122 A S a The IO module is defective.

Exchange the IO module.

123 A S a Communication error while accessing the

IO module.

Exchange the IO module.

124 iQ The configuration data was corrupt! The

configuration was restored using the
backup data.

125 a The limit value has alarm status.

126 W a The QAL3 data store is full. Please read

out the data.

Export QAL3 data.

127 W a The drift values exceed the QAL3 limits.

Repeat the calibration. Maintenance of
AMS required.

250 A S aQ The analyzer could not be found!

Check the connectors and cabling.

251 A S aQ The connection to the analyzer has been

lost!

Check the connectors and cabling.

252 A S aL The EEPROM data of the analyzer is

defective!

Check the configuration with TCT.

253 A S aL Communication with the analyzer is faulty! Check the connectors and cabling.
254 A S a The boot program of the analyzer is

defective! Notify Service!

Notify Service.

255 A S a The program of the analyzer is defective!

Notify Service!

Notify Service.

300 A S aL No new measured values from the

analog/digital converter.

Notify Service.

301 A S a The measured value exceeds the value

range of the analog/digital converter.

Check the sample gas concentration.
Check connectors in the gas analyzer.
Notify Service.

302 W aQ The offset drift exceeds half the

permissible range.

Monitor the drift. The measured value is
valid as long as the drift remains below the
value specified in the measurement data.
As soon as the drift exceeds this value,
notify Service.

303 A S aQ The offset drift exceeds the permissible

range.

Notify Service. Carry out a basic
calibration (with TCT).

Содержание EasyLine EL3020









































































































































Результаты поиска

Содержание EasyLine EL3020

Отзывы:

Похожие инструкции для EasyLine EL3020

Бренды по названию

Популярные бренды

ABB EasyLine EL3020, Инструкция по установке, запуску и эксплуатации

Результаты поиска

Содержание EasyLine EL3020

Отзывы:

Похожие инструкции для EasyLine EL3020

Бренды по названию

Популярные бренды