background image

  

63

 

 

 

 

 

 

 

Start-up

 

3ADW000197R0101 DCS800-R Sel e a

angle should be set to values higher than 95 degrees. Allow the system some 
moments to adapt to the new value. This limits the output voltage of the drive 
and gives a safe operation, even with a fault in the current feedback circuit. 
Precautions should be made do avoid to get EMF at the DC circuit (disable 
field current or block the motor), if the drive will be released and will generate 
current.  

 

Switch on the drive using the ON/OFF command. The RUN command has to 
remain in logic “0” level. This action causes the pulse firing logic to work and to 
generate single firing pulses at inverter limit position. No current should flow. 
Record the thyristor voltage (connection U1 – C1) and the firing pulse (e.g. by 
means of a current probe) and check the firing pulse position being at 150

°

el.  

 

Switch off the drive.  

 

Connect the gate leads to thyristor V14, 16 and 12.   

 

Switch on the drive using the ON/OFF command.  

 

No current should flow! Record the thyristor voltage and the firing pulse as be-
fore.  

 

Switch off the drive.  

 

Switch on the drive using the ON/OFF command. Set the RUN command to 
logic “1” level. Generate small current references within zero and limit discon-
tinuous / continuous current. Everything is o.k., if the current can be varied and 
does not hit the limit set by the parameter above or inverter limit position. De-
pending on the value of the minimum firing angle (perhaps higher than 120°

el

perhaps close to 150°

el

) it may happen, that there is either no current at all or a 

very small one. In this case change the settings step by step until a value 
around 100°

el

 reached. 

 

Switch off the drive. 

 

In case of trouble check the wiring for open loop or wrong connections. Do the 
check once again.   

 

In case the current can be varied by the reference and the power part consists 
of a reverse bridge go on with the same procedure used for the forward bridge. 
Keep the value of the parameter for minimum firing angle position. Check for 
correct connections. 

 

If current is flowing in forward and reverse direction in a controlled manner set the 
parameter for the minimum firing angle back to default. Check for the correct value 
for the parameter of the bridge changeover time.   

 

In case the power part consists of parallel bridges do the gate interconnections 
bridge per bridge and check for correct assignment. Do the commissioning of the 
other parallel bridges once again with the minimum firing angle set to high values 
because of safety reasons. 

 

When the gate connections are done and current is flowing in a controlled manner 
set the minimum firing angle position to default, the bridge changeover time to val-
ues necessary and go on with the other steps necessary to get the drive into op-
eration.   

 

Содержание DCS800



































































Отзывы: