ABB Baldor BC200 Скачать руководство пользователя

Страница: 9 / 24

2-3

MN716

Electrical Connections

To avoid erratic operation, do not bundle the AC line and motor wires with signal or control wiring.

Do not bundle motor wires from multiple controls in the same conduit. Use shielded cables on all

signal wiring over 12 (30 cm). The shield should be earth grounded on the control side only. Wire the

control in accordance with the National Electrical Code requirements and other local codes that may

apply.

AC LINE

Verify the AC line voltage matches the line voltage of the control. Connections are shown in Figure 2-2.

The BC200/BC201 has a single AC line fuse connected in series with terminal L1. Fuse (F1) is

25A for BC201 and 20A for BC200). Be sure to fuse each conductor which is not at ground potential

(do not fuse neutral or grounded conductors).

A separate AC line switch or contactor must be connected as a disconnect switch so that contacts

open each ungrounded conductor. See Table 2-1.

Table 2-1 Terminal Block Wiring Information

Terminal Block

Designation

Connection

Designation

Supply Wire Gauge

(AWG - Copper)

Maximum Tightening

Torque

(lbs- in)

Minimum

Maximum

TB1 (Power Board)

F+, F-

3.5

TB2 (Power Board)

L1, L2, M1, M2, GND

3.5

TB1 (Logic Board)

Logic Connections

3.5

Figure 2-2 Power Connections

FIELD

AC LINE

FUSE

TB1

ARMATURE

F+ F-

L1 L2 M1 M2

TB2

AC LINE

INPUT

Ground Connection

Connect all ground wires (earth) to the green ground screw that is provided on the inside of the

control to the right side of TB1 (not shown), tighten to correct torque, Table 2-1.

Motor Armature Connection

Connect the motor armature positive lead (+) to Terminal M1 and negative lead (-) to Terminal M2, as

shown in Figure 2-2.
An armature fuse (F2) is also provided with a rating equal to the maximum RMS rating of the control.

It is recommended that the correct size armature fuse be installed, depending on the rating of the

motor and form factor (RMS/AVG current). Fuse type should be Littlefuse 326 ceramic or Buss ABC, or

equivalent. A fuse chart is presented in Table 2-2, which suggests appropriate armature fuse ratings.

However, the specific application may require larger fuse ratings based on ambient temperature, CL

set point and duty cycle of operation.

StockCheck.com

Downloaded from StockCheck.com

Содержание Baldor BC200

























Результаты поиска

Содержание Baldor BC200

Отзывы:

Похожие инструкции для Baldor BC200

Бренды по названию

Популярные бренды

ABB Baldor BC200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Baldor BC200

Отзывы:

Похожие инструкции для Baldor BC200

Бренды по названию

Популярные бренды