ABB Baldor BC200 Скачать руководство пользователя

Страница: 7 / 24

2-1

MN716

Chapter 2

Installation

WARNING: Do not use this drive in an explosive environment. An explosion can cause serious or fatal injury.

This drive is not explosion proof.

Mounting

Mount the BC200/BC201 in a vertical position (connection terminals in down or up position) on a flat

surface free of moisture, metal chips, or corrosive atmosphere. Mount the control in such a manner

that there is unrestricted air flow through the heatsink cooling fins.

Note: If drive is mounted in other than a vertical position, decrease maximum allowable ambient

temperature by 10°C.

A 5K ohm Remote Speed potentiometer is provided with each control. Install potentiometer using

hardware provided. Be sure to install insulating disk between potentiometer and inside of
front panel.
Enclosure - When mounting the BC200 or BC201 in an enclosure, it must be large enough to allow for

proper heat dissipation. A 12x12x24 enclosure is suitable for the BC200 at full rating and a 12x24x36

enclosure is suitable for the BC201 at full rating. Smaller enclosures may be used if full rating is not

required or if adequate ventilation, or auxiliary cooling methods are used.

Figure 2-1A Mounting Hole Locations

RO.172

[R4.4] (4 PL)

0.324

[8.2] (4 PL)

RO.089

[R2.3] (4 PL.)

Note: CONTROL SHOWN ABOVE IS MODEL BC201.

HEIGHT OF MODEL BC200 IS 2.57" (65mm).

8.00

[203.20]

7.10

[180.34]

3.440

[87.4]

L1 L2 M1 M2

TB1

0.30

[7.62]

7.70

[195.58]

10.00

[254.00]

FWD ACC REV ACC DB OFFSET

MAX SPD RESP IR COMP REV CL FWD CL TCL

1 2 3 4 5 6 7 8 9 10 11 12 13

CON3

TB1

L2 L1 A2 A1 COM +20V B4 B3 B2 B1

CON1

CON2

0.60

[14.7]

StockCheck.com

Downloaded from StockCheck.com

Содержание Baldor BC200

























Результаты поиска

Содержание Baldor BC200

Отзывы:

Похожие инструкции для Baldor BC200

Бренды по названию

Популярные бренды

ABB Baldor BC200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Baldor BC200

Отзывы:

Похожие инструкции для Baldor BC200

Бренды по названию

Популярные бренды