manualshive.com logo in svg

ABB ACS880-104, Руководство по оборудованию

Поделиться
Скачать
ABB ACS880-104 Скачать руководство пользователя страница 198

LEDs and other status indicators

￭

Control panel and panel platform/holder LEDs

The ACX-AP-x control panel has a status LED. The control panel mounting platform or
holder has two status LEDs. For their indications, see the following table.

Indication

LED

Location

The unit is functioning normally.

Continuous green

Control panel

Data is transferred between the PC and the unit through the USB
connection of the control panel.

Flickering green

There is an active warning in the unit.

Blinking green

There is an active fault in the unit.

Continuous red

There is a fault that requires the stopping and restarting of the
drive/converter/inverter.

Blinking red

The Bluetooth interface is enabled, in discoverable mode, and
ready for pairing.

Blinking blue (ACS-
AP-W only)

Data is being transferred through the Bluetooth interface of the
control panel.

Flickering blue
(ACS-AP-W only)

There is an active fault in the unit.

Red

Control panel
mounting platform or
holder (with the con-
trol panel removed)

Power supply for the control unit is OK.

Green

￭

R8i module LEDs

Frame R8i modules have three LEDs. For their indications, see the following table.

Indication

LED

Location

There is an active fault in the module.

FAULT

(continuous red)

R8i module

The module is ready for use.

ENABLE / STO

(continuous green)

XSTO connectors are de-energized.

ENABLE / STO

(continuous yellow)

Supply voltage of the internal circuit boards is OK (> 21 V).

POWER OK

(continuous green)

Reduced run

A “reduced run” function is available for inverter units consisting of parallel-connected inverter
modules. The function makes it possible to continue operation with limited current even if
one (or more) module is out of service, for example, because of maintenance work. In
principle, reduced run is possible with only one module, but the physical requirements of
operating the motor still apply; for example, the modules remaining in use must be able to
provide the motor with enough magnetizing current.

The wiring accessories needed during the procedure are available from ABB.

198 Maintenance

Содержание ACS880-104























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды