![background image](http://html.mh-extra.com/html/abb/acs850-04-series/acs850-04-series_hardware-manual_2582129.webp)
Technical data
129
Losses, cooling data and noise
Terminal and lead-through data for the power cables
The maximum accepted cable size is 4 × (3 × 240) mm
2
or 4 × (3 × 500 AWG).
Screw size for connecting busbars to the drive module input and output busbars:
M12, tightening torque 50...75 N·m.
Units with optional common mode filter (+E208)
The additional busbars are included in the delivery of units with optional common
mode filter (+E208). The output busbars of the drive module can be enhanced with
the additional busbars in units without optional cabling panels (no +H381 or +H383).
Then, the maximum accepted cable size is 4 × (3 × 240) mm
2
or 4 × (3 × 500 AWG).
Screw size for connecting busbars to the drive module input and output busbars:
M12, tightening torque 50...75 N·m.
Units with optional cabling panels (+H381 or +H383)
The maximum accepted cable size is 4 × (3 × 240) mm
2
or 4 × (3 × 500 AWG). The
cabling panels are connected to the drive module busbars with M12 serpress nuts,
tightening torque 30 N·m (20 lbf·ft).
Input, motor and brake resistor cable terminal sizes and tightening torques are given
below.
Two-hole 1/2 inch diameter cable lugs can be used.
Drive type
ACS850-04
Frame
size
Air flow
Heat dissipation
Noise
m
3
/h
ft
3
/min
W
dB(A)
-387A-5
G1
1200
707
4403
72
-500A-5
G1
1200
707
5602
72
-580A-5
G1
1200
707
6409
72
-650A-5
G1
1200
707
8122
72
-710A-5
G2
1200
707
8764
72
-807A-5
G2
1200
707
9862
72
-875A-5
G2
1420
848
10578
71
U1, V1, W1, U2, V2, W2, UDC+, UDC-, R+, R-
Grounding busbar
Screw
Tightening torque
Screw
Tightening torque
N-m
N-m
M12
50...75
M10
30...44
U1, V1, W1, U2, V2, W2, UDC+, UDC-, R+, R-
Grounding busbar
Screw
Tightening torque
Screw
Tightening torque
lbf·ft
lbf·ft
1/2
37...55
3/8
22...32
Содержание ACS850-04 series
