ABB ACQ810 Скачать руководство пользователя страница 315 | Manualshive

Страница: 315 / 376

ABB ACQ810 Скачать руководство пользователя страница 315

Fault tracing 315

2008

ID-RUN
(0xFF84)

Motor identification run is
on.

This alarm belongs to normal start-up
procedure. Wait until drive indicates that
motor identification is completed.

Motor identification is
required.

This alarm belongs to normal start-up
procedure.
Select how motor identification should be
performed, parameter

Start identification routines by pressing
Start key.

2009

EMERGENCY STOP
(0xF081)

Drive has received
emergency stop command
(OFF1/OFF3).

Check that it is safe to continue
operation.
Return emergency stop push button to
normal position (or adjust the fieldbus
Control Word accordingly).
Restart drive.

2013

DEVICE OVERTEMP
(0x4210)

Measured drive temperature
has exceeded internal alarm
limit.

Check ambient conditions.
Check air flow and fan operation.
Check heatsink fins for dust pick-up.
Check motor power against unit power.

2014

INTBOARD OVERTEMP
(0x7182)

Interface board (between
power unit and control unit)
temperature has exceeded
internal alarm limit.

Let drive cool down.
Check for excessive ambient
temperature.
Check for cooling fan failure.
Check for obstructions in the air flow.
Check the dimensioning and cooling of
the cabinet.

2017

FIELDBUS COMM
(0x7510)

Programmable alarm:

Comm loss func

Cyclical communication
between drive and fieldbus
adapter module or between
PLC and fieldbus adapter
module is lost.

Check status of fieldbus communication.
See appropriate User’s Manual of
fieldbus adapter module.
Check settings of parameter group

.

Check cable connections.
Check if communication master is able to
communicate.

2018

LOCAL CTRL LOSS
(0x5300)

Programmable alarm:

Local ctrl loss

Control panel or PC tool
selected as active control
location for drive has
ceased communicating.

Check PC tool or control panel
connection.
Check control panel connector.
Replace control panel in mounting
platform.

2019

AI SUPERVISION
(0x8110)

Programmable alarm:

AI superv func

An analog input has
reached limit defined by
parameter

Check analog input source and
connections.
Check analog input minimum and
maximum limit settings.

2020

FB PAR CONF
(0x6320)

The drive does not have a
functionality requested by
PLC, or requested
functionality has not been
activated.

Check PLC programming.
Check settings of parameter group

.

2021

NO MOTOR DATA
(0x6381)

Parameters in group 99
have not been set.

Check that all the required parameters in
group 99 have been set.

Code

Alarm (fieldbus code),
other information

Cause

What to do

«
...
313
314
315
316
317
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды