manualshive.com logo in svg

ABB ACH550 series, Руководство по установке

Поделиться
Скачать
ABB ACH550 series Скачать руководство пользователя страница 14

Installation of the module

14

Power cable

The power cable provides 
connection to the drive’s 
internal 24 V DC connector on 
drive terminal 10 and 11. 

The cable is pre-configured 
and does not need to be 
changed. 

If you wish to use an external 
power source, disconnect the 
power cable from the terminal 
block (green connector). 

Connect the external power supply to this connector (AC or DC; 
for the power range, see 

Technical data

 on page 35).

MS/TP cable

The BACnet MS/TP cable 
provides connection to the 
drive’s MS/TP connector on 
terminals 29, 30 and 31. The 
cable is pre-configured and 
does not need to be changed.

It is recommended to use 
Belden 9842 or equivalent 
cable. Belden 9842 is a dual 
twisted, shielded pair cable 
with a wave impedance of 
120 ohms.

Crossover network cable

The router module package contains a crossover network cable. 
The cable is inside the package under a lid. Use this cable only for 
commissioning the router module. It is not designed to be used for 
any other purpose after commissioning the module.

Содержание ACH550 series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды