ABB ABILITY SSC600 Скачать руководство пользователя страница 67

Страница: 67 / 70

Glossary

ACT

1. Application Configuration tool in PCM600
2. Trip status in IEC 61850

Circuit breaker

CFG

Configuration file

COMTRADE

Common format for transient data exchange for power systems. Defined

by the IEEE Standard.

DAN

Doubly attached node

DAT

1. Data attribute type

2. Data file

Data set

The content basis for reporting and logging containing references to the

data and data attribute values

1. Direct current
2. Disconnector
3. Double command

DHCP

Dynamic Host Configuration Protocol

Definite time

EMC

Electromagnetic compatibility

Ethernet

A standard for connecting a family of frame-based computer networking

technologies into a LAN

GOOSE

Generic Object-Oriented Substation Event

GPS

Global Positioning System

HMI

Human-machine interface

HTTPS

Hypertext Transfer Protocol Secure

Hardware

IEC

International Electrotechnical Commission

IEC 61850

International standard for substation communication and modeling

IEC 61850-8-1

A communication protocol based on the IEC 61850 standard series

IEC 61850-9-2

A communication protocol based on the IEC 61850 standard series

IEC 61850-9-2

Lite Edition of IEC 61850-9-2 offering process bus interface

IED

Intelligent electronic device

IEEE

Institute of Electrical and Electronics Engineers, Inc.

IEEE 1588 v2

Standard for a Precision Clock Synchronization Protocol for networked

measurement and control systems

Internet Protocol

IP address

A set of four numbers between 0 and 255, separated by periods. Each serv-

er connected to the Internet is assigned a unique IP address that specifies

the location for the TCP/ IP protocol.

LAN

Local area network

1MRS758850 D

Glossary

SSC600

Operation Manual

Содержание ABILITY SSC600






































































Результаты поиска

Содержание ABILITY SSC600

Отзывы:

Похожие инструкции для ABILITY SSC600

Бренды по названию

Популярные бренды

ABB ABILITY SSC600, Руководство по эксплуатации

Результаты поиска

Содержание ABILITY SSC600

Отзывы:

Похожие инструкции для ABILITY SSC600

Бренды по названию

Популярные бренды