ABB 266FF Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 56

background image

2600T Series Pressure transmitters |

OI/266/FF-EN Rev. B 37

10 HMI local indicator

10.6 LCD structure

The Device TAG and Node Address are always visible in the
top side of the LCD. The line/s and bar-graph view depends by
the

HMI_MODE

Selection

The displayed variables are identified by a max of the three
character strings visible on the left side of the value when two
lines mode is selected or below the value when one line mode
is selected. The list of all the strings identifying the variable is
available in the

HMI_VARIABLE_1

within the HMITB table, see

“APPENDIX A – Device Data Blocks”.

Example of how the indicator looks with one and two
lines plus bar-graph

1 Tag | 2 Node address | 3 Variable identification | 4 Line 1 |
5 Line 2 | 6 Bar-graph

10.7 LCD setting

The variables to be displayed can be selected in two ways:

—

Locally using the optional LCD keypad from the menu

“Display/settings/…”

see APPENDIX B for further

information.

—

From remote station via Fieldbus communication writing

in the HMITB.

In the HMITB there are up to 4 variables called

HMI_

VARIABLE_x

(where x is from 1 to 4) and each of them can be

set with one variable to be displayed, selected from a list of 10
different variables.

Then the

HMI_LINE_1, HMI_LINE_2

and

HMI_BARGRAPH

must be set to one of the

HMI_VARIABLE_x

depending by

which variable the user wants see on the Line 1 or Line 2 or
bar-graph. The parameter

HMI_SEQUENCE

allows the

enabling of the automatic scrolling of the 4

HMI_VARIABLE_x

3

1

2

3

4
5

6

Figure 47: Display layout

Important.

It is recommended to use the Auto-scrolling only with

HMI_MODE set to One Line..

10.8 HMI as Diagnostic Indicator

While the HMI works as Variable Indicator, also diagnostic
strings can be displayed. Whenever a failure or warning
condition is detected within the transmitter, a message appears
in the low side of the display below the bar-graph.

The message is formed by the NAMUR NE107 icon and the
string of the component where the problem occurred.

NAMUR icons

Description

Source of error

Error / Failure

ELECTRONICS

Functional check (e.g. during
simulation )

SENSOR

Out of Spec (e.g. Sensor temperature
outside the specs limits)

PROCESS

Maintenance required

CONFIGURATION

Example of “Maintenance / Sensor” and “Failure /
Electronics” diagnostic

Figure 48: Diagnostic messages

«
...
35
36
37
38
39
...
»

Содержание 266FF

























































Отзывы:

Нет отзывов

Похожие инструкции для 266FF

Бренд: Panasonic Страницы: 2

Бренд: WDS Страницы: 32

Бренд: M-system Страницы: 2

65-2646XL-05-04

Бренд: RKI Instruments Страницы: 66

Бренд: National Instruments Страницы: 43

Бренд: XRadio Страницы: 29

Бренд: Yaesu Страницы: 39

Бренд: Northern Страницы: 4

Бренд: RF Limited Страницы: 4

FTDX5000D HF - PRODUCT REVIEW 12-2010

Бренд: Yaesu Страницы: 6

Бренд: Hach Страницы: 116

Бренд: Rockville Страницы: 8

Бренд: YOKOGAWA Страницы: 2

Бренд: Jamara Страницы: 8

Бренд: CommRadio Страницы: 27

MONARCH 318DOPW2K-C

Бренд: Transmitter Solutions Страницы: 2

Бренд: Lumel Страницы: 20

Бренд: Intek Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды