manualshive.com logo in svg

ABB 266 HART Series, Инструкция по эксплуатации

Поделиться
Скачать
ABB 266 HART Series Скачать руководство пользователя страница 26

26   OI/266/HART-EN Rev. M 

| 2600T Series Pressure transmitters

5 Mounting

5.14.3 Liquid level measurements on closed tanks 
and non condensable fluids (dry leg)

— Mount the transmitter at the same height or below the 

lowest level to be measured.

— Connect the + (H) side of the transmitter to the bottom of 

the tank.

— Connect the - (L) side of the transmitter to the upper part 

of the tank, above the maximum level of the tank.

5.14.4 Liquid level measurement with closed tanks and 
condensable fluids (wet leg)

— Mount the transmitter at the same height or below the 

lowest level to be measured.

— Connect the + (H) side of the transmitter to the bottom of 

the tank.

— Connect the - (L) side of the transmitter to the upper part 

of the tank.

— Fill the vertical section of the connecting line to the upper 

part of the tank with a compatible liquid through the 
dedicated filling tee.

Figure 33: Level measurement on closed tank with dry leg

Figure 34: Level measurement on closed tank with wet leg

5.14.5 Liquid level measurement with open tanks

— Mount the transmitter at the same height or below the 

lowest level to be measured.

— Connect the + (H) side to the bottom of the tank.

— Vent the “–” (L) side of the transmitter to the atmosphere 

(in this case a gauge pressure is shown; the (L) side is 
already vented to the atmosphere).

Figure 35: Level measurement on open tank with P style transmitter

Содержание 266 HART Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды