Abatron bdiGDB Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 60

background image

bdi

GDB

for GNU Debugger, BDI2000 (ARM11 / Cortex)

User Manual

28

© Copyright 1997-2014 by ABATRON AG Switzerland

V 1.21

MEMACCES mode [wait [hprot]]

For Cortex, this parameter defines how memory is accessed. Either via
the ARM core by executing ld and st instructions or via the AHB/AXI ac-
cess port. The current mode can also be changed via the Telnet interface.
The optional wait parameter allows to define a time the BDI waits before it
expects that a value is ready or written. This allows to optimize download
performance. The wait time is (8 x wait) TCK’s in Run-Test/Idle state. The
hprot option allows to define the CSW[31:24] bits in the AHB/AXI-AP.
For Cortex-M3, only AHB access is supported.
The following modes are supported:

CORE

The CORE (default) mode requires that the core is halt-
ed and makes use of the memory management unit
(MMU) and cache.

AHB or AXI

The AHB or AXI access mode can access memory even
when the core is running but bypasses MMU and cache.

SAP

For LS1000 devices a special memory acess mode is
available via the so called System Access Port (SAP)

Example:

MEMACCES CORE 5 ; 40 TCK's access delay
MEMACCES AHB 4 ; access via AHB, 32 TCK delay

SIO port [baudrate]

When this line is present, a TCP/IP channel is routed to the BDI’s RS232
connector. The port parameter defines the TCP port used for this BDI to
host communication. You may choose any port except 0 and the default
Telnet port (23). On the host, open a Telnet session using this port. Now
you should see the UART output in this Telnet session. You can use the
normal Telnet connection to the BDI in parallel, they work completely in-
dependent. Also input to the UART is implemented.

port

The TCP/IP port used for the host communication.

baudrate

The BDI supports 2400 ... 115200 baud

Example:

SIO 7 9600 ;TCP port for virtual IO

DCC port

When this line is present, a TCP/IP channel is routed to the ARM debug
communication channel (DCC). The port parameter defines the TCP port
used for this BDI to host communication. You may choose any port except
0 and the default Telnet port (23). On the host, open a Telnet session us-
ing this port. Now you should see the DCC output in this Telnet session.
NOTE: Only core#0 and core#1 support this DCC routing.

port

The TCP/IP port used for the host communication.

Example:

DCC 7 ;TCP port for DCC I/O

DAPPC address

This parameter is necessary for some TI processors (for example
OMAP3, OMAP4, ...). It defines the address/number of a special debug/
clock/power/reset control register. If the address is >=0x80000000 (bit31
set) then this register is accessed via the APB memory space. Otherwise
it defines an ICEPick register.

address

APB address or ICEPick register block/number

Example:

DAPPC 0xD4159008 ;DAP-PC Cortex-A9#0
DAPPC 0xD415900C ;DAP-PC Cortex-A9#1
DAPPC 0x60

;non-JTAG register 0

«
...
26
27
28
29
30
...
»

Содержание bdiGDB





























































Отзывы:

Нет отзывов

Похожие инструкции для bdiGDB

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: SAMCHULLY Страницы: 48

Бренд: Vahle Страницы: 96

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды