background image

1.   Read these instructions.

2.   Keep these instructions.

3.   Heed all warnings.

4.   Follow all instructions.

5.   Clean the amplifier only with a dry, lint-free 

  cloth. For more thorough cleaning, unplug 

  the amplifier from the mains supply and go 

  over it lightly with a damp, lint-free cloth. 

  Do not use any type of chemical solvents or 

  other cleaning products for cleaning.

6.   Do not install near any heat sources such 

  as radiators, heat registers, stoves, or other 

  apparatus (including amplifiers) that 

  produce heat.

7.   Protect the power cord from being walked 

  on or pinched particularly at plugs, conve-

  nience receptacles, and the point where 

  they exit from the apparatus.

8.   Unplug this apparatus during lightning 

  storms or when unused for long periods 

  of time.

9.   Do not defeat the safety purpose of 

  the polarized or grounding-type plug.

10. Only place apparatus horizontally and on 

  a suitable table or rack. If more components are  

  stacked. Make sure to place the hottest unit -  

  usually the amplifier, at the top

11. Refer all servicing to qualified service 

 personnel.

12. Servicing is required when the apparatus 

  has been damaged in any way, such as when 

  the power-supply cord or plug is damaged, 

  liquid has been spilled or objects have fallen 

  into the apparatus, the apparatus has been 

  exposed to rain or moisture, does not 

  operate normally, or has been dropped.

1.  

WARNING

 

 

– Take care that objects do not 

  fall and liquids are not spilled into the 

  enclosure through any openings. 

  The equipment shall not be exposed to 

  dripping or splashing. Liquid-filled objects 

  such as vases should not be placed on the 

 equipment.

2.   The equipment has been designed for use in 

  moderate climates and in domestic 

 situations. 

3.   Only connect the equipment to a power 

  supply of the type described in the operating 

  instructions or as marked on the equipment.  

  The primary method of isolating the 

  equipment from the mains supply is to 

  remove the mains plug. The equipment must 

  be installed in a manner that makes dis-

  connection possible. 

4.   If an abnormal smell or smoke is detected 

  from the equipment, turn the power off 

  immediately and unplug the equipment from 

  the wall outlet. Contact your dealer and do 

  not reconnect the equipment.

THE EQUIPMENT SHOULD BE SERVICED BY QUALIFIED SERVICE PERSONNEL 

Содержание C-280











Отзывы: