Aardvark VANSAT Raven Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 16

Aardvark VANSAT Raven Скачать руководство пользователя страница 14

14

USING AN EXTERNAL PAYTV DECODER

AND

A VAST Decoder

For installations where the customer has both a VAST Decoder as well as a
PayTV decoder, connect the spare white coax cable from the roof to the
VAST decoder as above. For the PayTV decoder connect the short loop
coax cable (supplied) from the “Loop Out” socket on the rear of the
MOTOSAT Control Unit (see earlier pages for the location) to the LNB input
on the users PayTV decoder.

PAYTV DISCLAIMER

Using Your Satellite Pay TV Service With The VANSAT System May Violate
Your Providers Terms and Conditions. Aardvark Electronics (Producers of
the VANSAT System) encourages Pay TV subscribers that are considering
travelling with their service to contact their provider to check the OK
regarding the use of their equipment and service outside of the place it was
installed into.

CLOSING THE SYSTEM DOWN

Pressing the power (standby) button on the remote will cause the dish to
rotate home and lower. Before travelling, the dish should be visually
checked to confirm this has taken place.

DO NOT rely solely on the ignition

signal as a guarantee that the dish has lowered.

«
...
12
13
14
15
16
»

Содержание VANSAT Raven

















Отзывы:

Нет отзывов