manualshive.com logo in svg

AAON SS1068, Техническое руководство

Поделиться
Скачать
AAON SS1068 Скачать руководство пользователя страница 75

     VAV/ZONE CONFIGURATION

VCC-X Operator Interface SD

 

75

VAV/Zone Setpoint Screens

 VAV/Zone Controller Setpoints

Modular Service Tool Instructions

From any menu screen, 

press

 

<SETPOINTS>

. The 

Unit Selection 

Screen,

 shown below, 

will appear requesting that you enter the unit 

ID number. 

Enter Unit Address

Then Press Enter

Selected Unit#: XXXX

No Communication

Enter

 the correct unit ID number of the Controller you want to 

change Setpoints for and

 press

 

<ENTER>

. Once communication 

is established, “No Communication” will be replaced with “Press 
Down.” You will then see Setpoint Screen #1. 

Press

 

<ENTER> 

to 

save entered data and

 

press

 

<

> 

to scroll through the screens.

NOTE: 

 If “No Communication” remains, it indicates a 

communication failure to the controller.

System Manager SD Instructions

From any Main screen, 

press

 

<SETPOINTS>

. The screen below 

will appear because this option requires passcode clearance. Only a 
Level 2 passcode can change setpoints. 

THIS ACTION REQUIRES

PASSCODE CLEARANCE

Enter Passcode: XXXX

If the correct passcode was entered, the 

Unit Selection Screen

 will 

be displayed. 

Enter Unit Address

Then Press Enter

Selected Unit#: XXXX

No Communication

Enter the Unit ID of the controller you wish to change setpoints 
for and 

press

 

<ENTER>

. Once communication is established, “No 

Communication” will be replaced with “Press Down.”  

NOTE: 

 If “No Communication” remains, it indicates a 

communication failure to the controller.

The following screen will be displayed: 

Change Setpoints
Configure Unit

Save/Copy/Restore

Scroll to the ‘Change Setpoints’ option and 

press

 

<ENTER>

.   This 

will take you to the 

fi

 rst Setpoints Screen shown below.

Setpoint Screen #1 -    Occupied Setpoints

XX Box Spts IDXXXX
Occupied Setpoints

Cooling.....:   XX

º

F

Heating.....:   XX

º

F

Enter the 

Occupied Cooling Setpoint

 as the maximum temperature 

you would like the zone to reach before modulating the damper 
open to bring in more cold air to cool the space. Enter the 

Occupied 

Heating Setpoint

 as the minimum temperature you would like the 

zone to reach before activating the Reheat Stages on the optional 
Expansion Relay board. If this is a Cooling Only box that doesn’t 
contain reheat, this setpoint will be ignored.

Description

Minimum

Default

Maximum

Cooling Setpoint

50ºF

74ºF

90ºF

Heating Setpoint

50ºF

70ºF

90ºF

Setpoint Screen #2 -    Unoccupied Setbacks

XX Box Spts IDXXXX

Unoccupied Setbacks

Cooling SetUp:  XX

º

F

Heating SetBk:  XX

º

F

During unoccupied hours, the Occupied Cooling Setpoint is adjusted 
up by the amount entered for the Cooling SetUp. The Occupied 
Heating Setpoint is adjusted down by the amount entered for the 
Heating SetBk.  

Description

Minimum

Default

Maximum

Cooling SetUp

0ºF

+10ºF

+30ºF

Heating SetBk

0ºF

-10ºF

-30ºF

Содержание SS1068



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды