manualshive.com logo in svg

AAON SS1068, Техническое руководство

Поделиться
Скачать
AAON SS1068 Скачать руководство пользователя страница 39

VCC-X Operator Interface SD

 

 VCC-X CONFIGURATION

39

VCC-X Con

fi

 guration Screens

 Table 5:  User-Con

fi

 gurable  Relay Outputs

No.  Relay Description

 Details

  1

   Cooling Stage

Con

fi

 gured for each 

fi

 xed stage of cooling (except heat pump compressor).

  2

   Heating Stage

Con

fi

 gured for each 

fi

 xed stage of heating. 

  3

   Aux Heat

Con

fi

 gured for a 

fi

 xed stage of Aux Heat in a heat pump unit.

  4

    Emergency Heat

Con

fi

 gured for a 

fi

 xed stage Emergency Heat in a heat pump unit.

  5

   Mod Heat Enable

Con

fi

 gure if a 0-10 VDC Modulating Heat source needs a relay to enable it.

  6

   Mod Cool Enable

Con

fi

 gure if a 0-10 VDC Modulating Cool source needs a relay to enable it.

  7

  Morning Warm-Up/
Cool-Down (VAV Boxes)

Con

fi

 gure (1) Relay for Morning Warm-Up/Cool-Down when Non-Orion VAV/Zone Controllers 

are used.

  8

 Reheat 

Con

fi

 gure (1) Relay for On/Off Reheat when used.

  9

   Pre-Heat

Con

fi

 gure for Pre-Heat operation. 

 10

   Low Ambient 

Con

fi

 gure for Low Ambient operation. 

 11

 Exhaust Fan

Con

fi

 gure (1) Relay for enabling exhaust fan when Building Pressure Control is used.

 12

   Economizer Active

If con

fi

 gured, this relay will energize if unit is in Economizer mode and the damper has moved 

5% above its Economizer Minimum Setpoint position.

 13

 Heat Wheel 

Con

fi

 gure (1) Relay that turns heat wheel on when in occupied operation and turns heat 

wheel off when in Economizer Mode.

 14

   Occupied Active

If con

fi

 gured, this relay will energize whenever the unit is in the Occupied Mode.

 15

   Override Active

If con

fi

 gured, this relay will energize anytime the space sensor Push-button override is active.

 16

   Alarm Active

If con

fi

 gured, this relay will energize anytime a VCC-X alarm is active.

 17

Liquid Line 1 Solenoid - EXV 1

Con

fi

 gure (1) Relay for RSMV or RSMV-HP Expansion Valve 1.

 18

Liquid Line 2 Solenoid - EXV 2

Con

fi

 gure (1) Relay for RSMV or RSMV-HP Expansion Valve 2.

 19

Liquid Line 3 Solenoid - EXV 3

Con

fi

 gure (1) Relay for RSMV-HP Expansion Valve 3.

 20

Liquid Line 4 Solenoid - EXV 4

Con

fi

 gure (1) Relay for RSMV-HP Expansion Valve 4.

Содержание SS1068



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды