Aanderaa DCPS 5400 Скачать руководство пользователя страница 73

Страница: 73 / 150

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Page 73

If the DCPS is running in a slow recording group in the multi-group recorder (more information about the Multi-group

recorder is available in the TD 303 Chapter 3.3.1), it is possible to have the other sensors in a faster group to give more

frequent update of input parameters.

3.5.8

Input Parameter Conductivity

Figure 3-23: External conductivity sensor parameter input

Figure 3-23

gives an example of a conductivity sensor connected to the same Datalogger as the DCPS. The

Conductivity sensor is selected as

Conductivity Sensor Id

and the Conductivity(mS/cm) is selected as

Conductivity

Parameter Id..

When the DCPS receives input from these three sensors via the Datalogger, it is able to calculate the correct salinity,

depth and sound speed. These values are used for correct positioning of cells and the correct conversion from Doppler

shift to current speeds.

3.5.9

Input Parameter Heading

Figure 3-24: External compass sensor input

The sensor can also take an input from an external Compass, like for example the Airmar H2183 Compass. Surface

buoys are often made of steel. The magnetic influence from the buoy can give a big error on the compass heading

measured by the DCPS. A compass mounted on a mast away from the buoy structure is often a better method which

gives a more accurate compass measurement. Select a compass connected to the Logger in the

Heading Sensor Id

drop-down menu if available and the heading parameter in

Heading Parameter Id

. The

Heading Alignment Offset

(Deg.M)

value can be set to compensate for the misalignment between the compass axes and the axes on the DCPS.

When finished with the configuration, click

Next

twice and wait for the Datalogger to finish the saving of the new

configuration

Содержание DCPS 5400























































































































































Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды

Aanderaa DCPS 5400, Руководство по эксплуатации

Результаты поиска

Содержание DCPS 5400

Отзывы:

Похожие инструкции для DCPS 5400

Бренды по названию

Популярные бренды