A&D GX-A Series Скачать руководство пользователя | Manualshive

Страница: 35 / 52

background image

GX-A/GF-A Maintenance manual

Page 33

6.7 Coarse Operation Check & Adjustment

1. A/D count check

The A/D count can be checked in the check mode.
Follow  the  procedure  below  to  verify  the  A/D  values  for  weight  data  (D0)  and
temperature data (T1).

Step 1. Display the data adjustment mode

d-d5p

after getting into check mode shown on

page 28,29.

Step 2. Press the PRINT key to display

XXXX

. (D0 data, weight A/D count)

Step 3. Check that the pan assembly is installed properly. Verify that the count without load

(zero point) is within the range shown in the table below.

Note: If the zero point is not within the specification, adjust it by jumpers (JP2, JP3

on the main board).

Opening JP2 makes Zero point +2500(D0) and opening JP3 makes Zero point

+2500(D0).

Step 4. Place the mass in the table below on the pan. Read the count with load (full).

Subtract the count without load from the count with load to obtain the span value.
Verify that the span value and full value are within the range shown in the table below.

In the D0 data mode (Weight A/D count), press the SAMPLE key twice to display

X.XX (D2 data). Verify that the dispersion is within the specifications as below

when the mass is placed on the pan.

Model

Masses

Zeropoint

(D0)

Full (D0)

Span (D0)

Dispersion (D2)

GX-203A/303A/403A

603A/1003A/1603A

GF-123A203A/303A

403A/603A/1003A

1603A

1600g

1100~4000

9000

3700

～

5000

MAX-MIN:

0.002g/5seconds

GX-2002A/3002A/4002A

6002A/10002A

6001A/10001A

GF-1202A/2002A/3002A

4002A/6002A/10002A

6001A/10001A

10kg

1100~4000

~9000

3000

～

4200

MAX-MIN:

0.02g/5seconds

MAX-MIN:

0.1g/5seconds

Step 5. In the D2 data mode, press the SAMPLE key three times to display

XXXXXX

.

(T1 data)

Step 6. Verify that the count at room temperature (15-25°C) is within the range shown in the

table below.

Absolute value (T1 data)

Dispersion (T1 data)

2400000-2800000

MAX-MIN: 40 counts/5 seconds

«
...
33
34
35
36
37
...
»

Содержание GX-A Series





















































Отзывы:

Нет отзывов

Похожие инструкции для GX-A Series

valor 5000 series

Бренд: OHAUS Страницы: 56

Бренд: OHAUS Страницы: 196

DEFENDER SERIES

Бренд: OHAUS Страницы: 64

Бренд: OHAUS Страницы: 4

Style Sense Multi 100

Бренд: Soehnle Страницы: 38

Бренд: U-Line Страницы: 12

Бренд: Microlife Страницы: 32

Бренд: Sencor Страницы: 10

Бренд: Tree Страницы: 19

Бренд: Saturn Страницы: 18

Бренд: cecotec Страницы: 68

Бренд: Linea 2000 Страницы: 48

Бренд: Velleman Страницы: 26

Бренд: Nokia Страницы: 16

Бренд: Nokia Страницы: 16

Бренд: Nokia Страницы: 55

Бренд: Nokia Страницы: 63

Бренд: U.S. Solid Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды