Aalborg i/o 232 Скачать руководство пользователя страница 15

13

APPENDIX 4

Note: Follow Return Procedures In Section a.3.

Warranty

Aalborg  electronics  products  are  warranted  against  defects  in  parts
and workmanship for a period of one year from the date of purchase.
Proper  product  selection  is  the  responsibility  of  the  customer.  It  is
deemed the responsibility of the customer that only operators with at
least  basic  knowledge  of  the  equipment  and  it’s  limitations  are 
permitted  to  control  and  operate  the  equipment  covered  by  this 
warranty. Anything to the contrary will automatically void the liability of
Aalborg and the provisions of this warranty. Defective products will be
repaired or replaced solely at the discretion of Aalborg at no charge.

Shipping charges

are borne by the customer. 

This warranty is void if the equipment is damaged by accident or mis-
use, or has been repaired or modified by anyone other than Aalborg or
factory authorized service facility. This warranty defines the obligation of
Aalborg and no other warranties expressed or implied are recognized.

Астана +7(77172)727-132 Волгоград (844)278-03-48 Воронеж (473)204-51-73 Екатеринбург (343)384-55-89  

Казань (843)206-01-48 Краснодар (861)203-40-90 Красноярск (391)204-63-61 Москва (495)268-04-70

Нижний Новгород (831)429-08-12 Новосибирск (383)227-86-73 Ростов-на-Дону (863)308-18-15

Самара (846)206-03-16 Санкт-Петербург (812)309-46-40 Саратов (845)249-38-78 Уфа (347)229-48-12

Единый адрес: [email protected] Веб-сайт: aalborg.nt-rt.ru

Содержание i/o 232
















Отзывы: