background image

 

 

FOR DETAILS ON THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM, REFER TO THE INSTALLATION INSTRUCTIONS 
FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED. 

 

 

This device complies with Part 15 of the FCC rules and RSS210 of IC.  Operation is subject to the following two conditions:  (1) This device may not 

cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 

 

 

FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT 

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your 

information: 
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manu-

facturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a 

Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection 

against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this 

equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following measures: 
• 

If using an indoor antenna, have a quality outdoor antenna installed. 

• 

Reorient the receiving antenna until interference is reduced or eliminated.  

• 

Move the radio or television receiver away from the receiver/control. 

• 

Move the antenna leads away from any wire runs to the receiver/control. 

• 

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. 

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or installer may 

find the following booklet prepared by the Federal Communications Commission helpful:  "Interference Handbook" 
This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. 

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.  
Unauthorized changes or modifications could void the user's authority to operate the equipment. 

 

 

LIMITED WARRANTY 

Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 2 Corporate Center Drive, Suite 100, Melville, New 

York 11747, warrants its product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and 

workmanship under normal use and service for 24 months from the date stamp control on the product(s) or, for product(s) not having a 

manufacturer’s date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in 

which case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or 

labor, any product(s) which is proved not in compliance with Seller's specifications or proves defective in materials or workmanship under normal 

use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product(s) is altered or improperly repaired or 

serviced by anyone other than Honeywell factory service. Connection of any device(s) to a communicating bus of a Honeywell security system 

(e.g., keypad bus, polling loop) other than those manufactured or approved by Honeywell shall void this warranty.  For warranty service, return 

product(s) transportation prepaid, to your local authorized Honeywell representative. 
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, 

WHICH  EXTEND  BEYOND  THE  DESCRIPTION  ON  THE  FACE  HEREOF.  IN  NO  CASE  SHALL  SELLER  BE  LIABLE  TO  ANYONE  FOR  ANY 

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY 

OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. 
Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will prevent any personal injury 

or property loss by burglary, robbery, fire or otherwise; or that the product(s) will in all cases provide adequate warning or protection. Customer 

understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring 

without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as 

a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED 

ON  A  CLAIM  THAT  THE  PRODUCT(S)  FAILED  TO  GIVE  WARNING.  HOWEVER,  IF  SELLER  IS  HELD  LIABLE,  WHETHER  DIRECTLY  OR 

INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, 

SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE THE 

COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. 
This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s). No increase or alteration, written or 
verbal, of the obligations of this Limited Warranty is authorized. 

 
 

 

300-138 Portage Avenue East 
Winnipeg, Manitoba 
R3C 0A1 
204-949-0078 or  
866-949-0078 

 

302-1301 8th Street South West 
Calgary, Alberta 
T2R 1B7 
403-233-7454 or  
800-655-2644

 

15911-121A Avenue 
Edmonton, Alberta 
T5V 1B1 
780-421-8741 or  

800-688-2970

 

 
 

ÊK4460-6V47Š 

K4460-6V4   3/08  Rev A 

 

 

Содержание 6150RFAAA









Отзывы: