manualshive.com logo in svg

A2B Electronics ECX-200, Руководство по установке

Поделиться
Скачать
A2B Electronics ECX-200 Скачать руководство пользователя страница 10

10

4.3.4 Output settings

ASI

The output selection ASI disables all 

RF modulation on the outputs and all 

selected services will be transmitted 

only through the ASI output 

connector. ASI is a high speed 

interface for digital TV transport 

streams. Use this output mode if you 

run IPTV out.

Under 

[ASI options]

you can select 

the output bitrate which is the same 

bitrate as for IPTV out.

Analogue

The selection 

[Analogue]

is set as 

factory default as RF output .

You can select output 

[Channel 

name]

(E2 to E69) or 

[Frequency]

within steps of 1 kHz (for example 

306,167 MHz). Country specific 

settings can be done by selecting 

[Country]

. By selecting a specific 

country, transmission standard and 

languages are automatically preset. 

[Audio language]

gives you the 

choosen language if there is more 

than one language ín the received 

signal. 

[Audiolevel]

can be adjusted 

between 0 to -12 dB.

Subtitling type, subtitle priority and 

subtitle charset can be selected as 

well as Subtitle conversion and 

Subtitle WSS.

We suggest that you consult your service provider for correct 

parameters for each multiplex you want to receive.

Click [Output] to continue with the output settings.

4. Settings (continued)

English

Содержание ECX-200

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды