manualshive.com logo in svg

A to Z Rubber Stamps 01-07554-000170, Руководство пользователя

Поделиться
Скачать
A to Z Rubber Stamps 01-07554-000170 Скачать руководство пользователя страница 45

Disassembling Typesection: 

Numbering Machines (AN-E, ADN-E): 

The following instructions are to be used when it is necessary to remove or replace a 
worn part.   

Rotary Solenoid ( 

figure 25

) 

NOT RECOMMENDED ON FIELD REPAIRS 

-Remove return spring. 
-With printing wheels face down, move actuating pawl swing forward. 
-Using a thin punch (an old actuating pawl shaft (a) will do), tap the roll pin out. 
(Remove "E" ring (d) that secures the connecting arm if interfering with procedure.) 
-Loosen set screw (b) located on solenoid hub. 
-Remove the two hex nuts securing the rotary solenoid and pull solenoid out. 
-Insert new rotary solenoid and fasten with the two hex nuts. 
-Turn rotary solenoid's disc clockwise as far as it will go and hold. 
-With thumb of free hand, move actuator arm assembly (c) forward slowly until wheel 
"clicks".  Also make sure that hub of actuator arm assembly is about .050 away from 
the frame plate.  At this setting (w/rotary solenoid's disc still completely turned 
clockwise) tighten set screw (b) located on solenoid hub. 
-Turn frame over and back off bumper stop (e) until the screw head touches actuator 
arm assembly tab.  This acts as a convenient holding fixture for the next step. 
-Using a 1/8 drill, drill into existing hole on hub and through the shaft of the solenoid. 
-Insert a 1/8 Dia. x 9/16 roll pin into hole and drive into place. 
-Reinstall connecting arm, "E" ring and return spring. 
-Lower bumper stop screw (e) so that , while moving actuator arm assembly, wheel is 
just  short of "clicking" into place. 

01/04/2012

45

Содержание 01-07554-000170



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды