manualshive.com logo in svg

A.R.C. Laser Nuvolas, Руководство пользователя

Поделиться
Скачать
A.R.C. Laser Nuvolas Скачать руководство пользователя страница 36

User Manual NUVOLAS 

April 2023

 

 

 

File: User Manual_NUVOLAS_rev3.docx

 

 

 

36 

6.4  Inserting the applicator 

If the device is ready and the treatment can be started, the 
applicator can be connected to the device.  

All  fibers  and  probes  have  a  quick-release  connector.  The 
connectors  are  equipped  wit  an  anti-twist  protection, 
recoginzable by small notches in the connector.  

This  ensures  an  optimal  fit  in  the  fiber  coupling  for  a 
reproducable  prower  transmisstion.  The  connector  has  to 
snap in to use the laser device. In case the connector has not 
be  properly  connected,  the  device  will  not  change  into 
READY  mode.  Please  pay  attention  to  a  clearly  hearable 
"click" when inserting the connector! 

Once the connector has been locked in place, the treatment can start. At this point laser 
radiation can be emitted through the fiber if the foot switch is activated. 

6.5  READY- / Standby-Button 

After  starting  the  laser,  the  NUVOLAS  is  in  STANDBY  mode.  By 
pressing  the  button,  the  device  changes  into  READY  mode.  The 
transition  from  STANDBY  to  READY  takes  a  few  seconds,  which  is 
accompanied  by  an  acoustic  signal  and  a  blinking  attention  symbol. 
As  soon  as  the  NUVOLAS  is  in  READY  mode,  you  can  emit  laser 
radiation using the foot switch.  

By pressing the READY button again, the READ mode will be left and 
the device returns to STANDBY. 

6.6  Release laser radiation 

To emit laser radiation, press the foot switch. The laser must be switched to the READY 
mode to do so. 

 

When  a  laser shot  is fired,  a  simultaneous  warning  signal  is  audible  and  the  red  laser 
emission LED on the display lights up. 

6.7  Treatment 

Position the patient. Select the necessary laser settings. Press the READY button: The 
READY button in the display and the READY-LED light up yellow. The aiming beam is 
visible and the treatment can start. 

The software of the NUVOLAS allows to sum up the energy emitted permanently. 

Make sure that only one person at a time touches the NUVOLAS.  

A T T E N T I O N 

Any serious incident that occurrs with this laser must be reported to the A.R.C. Laser 
GmbH and the responsible state authority.  

Содержание Nuvolas

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды