background image

TR

OUBLE

SHOO

TING

 24 

 Residential Hybrid Electric Heat Pump Water Heater Use and Care Guide 

Water Heater Sounds

During the normal operation of the 

water heater, sounds or noises may be 

heard. These noises are common and 

may result from the following:

• 

Normal expansion and contraction 

of metal parts during periods of 

heat-up and cool-down.

• 

Sediment buildup on or around 

the elements could create varying 

amounts of noise and may cause  

premature tank failure. Drain 

and flush the tank as directed 

under the “Draining and Flushing” 

section.

• 

The heat pump compressor or fan 

running.

 

Temperature Too High

If the water temperature is too hot:

•   Adjust the UIM setting on the water 

heater (see Step 12 in the installation 

section of this manual). 

•   Install or adjust a Thermostatic 

Mixing Valve (see manufacturer’s 

instructions)

A nonfunctioning thermostat or a short

-

ed heating element can cause extremely 

hot water. If the Temperature and Pres-

sure Relief Valve (T&P Valve) releases 

large amounts of very hot water, it is 

likely due to a shorted heating ele

-

ment, or more rarely a nonfunctioning 

thermostat, or the thermostat does 

not fit snuggly against the tank.  Very 

high water temperatures can also cause 

the Energy Cut Off (ECO) to trip (see 

page24). Turn power off until this prob

-

lem is fixed.

Low Water Pressure

Check both the cold and hot water at a 

sink to determine if the lower pressure 

is only on the hot water side. If both hot 

and cold faucets have low pressure, call 

your local water utility. If the low pressure 

is only on the hot water side, the primary 

causes of this are:

•   Melted dip tube. Soldering copper 

pipes while they are connected to the 

water heater can melt the inside of the 

hot and cold water connections or the 

dip tube (cold water side). A melted 

dip tube can restrict the flow of hot 

water. If that’s the case, replace the dip 

tube. 

• 

Partially closed supply valve. Open the 

water heater’s supply valve fully.

Insufficient or No Hot 

Water or Slow Hot Wa

-

ter Recovery:

If the hot water is simply not warm 

enough, there are several possible 

causes:

•  Thermostatic mixing valve faulty or 

set too low. 

• 

Temperature set point too low. 

•  Hot water usage pattern exceeds the 

capability of the water heater in cur-

rent mode (See “Operating Mode  

Descriptions”).

• 

Water connections to unit are 

reversed (Disconnect and re-install 

correctly).

•  Leak in plumbing system (Check home 

for any leaks and repair).

•  Lower heating element not function

-

ing properly.

• 

No power to the water heater (No 

lights on the unit are on and display 

is blank).

• 

Unit is in Vacation Mode.

• 

ECO tripped.

•  Non-functioning upper temperature 

sensor (refer to “Diagnostic Codes” 

section E60).

• 

Air filter dirty (See “Air Filter Mainte-

nance” p.33).

•  Out of position outlet j-tube (Assure 

orientation of line on tube is in top 

position).

•  Lower heating element not function

-

ing properly.

Thermostatic Mixing Valves.

 If the 

hot water is simply not warm enough, 

make sure the faucet you are checking 

doesn’t have a defective Thermostatic 

Mixing Valve. If these devices fail, they 

can reduce the amount of hot water the 

shower or faucet delivers even though 

there is plenty of hot water in the tank. 

Always check the water temperature at 

several faucets to make sure the prob-

lem is not in a faucet or shower control.

TROUBLESHOOTING

Содержание ProLine XE

































Отзывы: