background image

24

4. GUARANTEE

The following conditions form the

guarantee agreement between A.O.
Smith Water Products Company (the
warrantor) and the owner of the water
heater.

4.1

Guarantee in general

If within one year of the original

installation date of the water heater any
part or component other than the tank
shall prove upon examination by the
warrantor or authorised agent to be
defective in material or workmanship,
the warrantor will exchange such part
or component.

4.2

Guarantee of the tank

If within 3 years of the original

installation date, the tank fails due to
rust or corrosion from the water side,
the warrantor will supply a complete
new water heater of equivalent size
and duty (excluding delivery and
installation charges). On the
replacement water heater a guarantee
will be granted sufficient to cover the
unexpired portion of the original 3 year
guarantee of the originally installed
water heater.

4.3

Conditions for installation
and use

The guarantee applies to the heater

only while it remains in its orignial
location, and is installed in accordance
with local plumbing and building
regulations and all relevant Codes of
Practice.

The water heater should also have

been used only:
a) for potable water free to circulate at

all times and with the tank free of
damaging scale deposits;

b) at temperatures not exceeding the

maximum setting of its thermostat
and ECO (Energy Cut Off device);

c ) at water pressures and/or energy

inputs which do not exceed those
stated on the rating plate of the
water heater;

d) in a non corrosive atmosphere or

area;

e) with an approved temperature and

pressure relief valve of adequate
capacity not exceeding the working
pressure rating shown on the water
heater, and installed in conformity
with A.O. Smith Water Products
Companies installation instructions;

f ) when anode(s) have been inspected

and renewed, if they are worn or
erroded by 50% of more at any point
of their length.

4.4

Exclusions

The guarantee will be null and void:

a) if the water heater has been

damaged by an external cause;

b) in case of misuse, neglect (including

frost damage) or incorrect use of the
water heater;

c ) in case of unauthorised alteration,

modification or repair;

d) in case of ingress into the water

heater of chemicals, pollutants or
contaminants;

e) if the hardness of the incoming

water is, or has been, softened
below 60 ppm CaCO

;

f ) if the water heater is effected by

corrosive vapours such as those
found in hairdressers, dry cleaners
and laundries or where some
industrial degreasing products are
used and stored (for further
information and advise please
contact the A.O. Smith Technical
Department).

4.5

Range of guarantee

All replacement water heaters supplied
under the terms of this warranty will be
supplied ex stock on an F.O.B. basis.
A.O. Smith accepts no responsability
for carriage, labour or other installation
costs.

4.6

Claims

Any claim under this warranty

should be initiated with the dealer who
originally sold the water heater or with
any other dealer or stockist of the
warrantors products.

Содержание EQ 280





























Отзывы: