A.O. Smith BT-100-LP Скачать руководство пользователя страница 11

Страница: 11 / 47

•

DO NOT

apply insulation to the top of the water

heater, as this will interfere with safe operation of the

draft hood. See

Figure 18

(page 20)

•

DO NOT

cover the thermostat or the temperature-

pressure relief valve.

•

DO NOT

allow the insulation to come within 2 inches

(5 cm) of the floor to prevent blockage of combustion

air flow to the burner.

•

DO NOT

cover the instruction manual. Keep it on the

side of the water heater or nearby for future reference.

•

obtain new warning and instruction labels from

the manufacturer for placement on the blanket directly

over the existing labels.

•

inspect the insulation blanket frequently to make

certain it does not sag, thereby obstructing the

combustion air flow.

HARD WATER

Where hard water conditions exist, water softening or the

threshold type of water treatment is recommended. This

will protect the dishwashers, coffee urns, water heaters,

water piping and other equipment. See the

Periodic

Removal of Lime Deposits From Tank Type Commercial

Water Heaters

(page 30) for sediment and lime scale

removal procedures.

CIRCULATION PUMPS

A circulating pump is used when a system requires

a circulating loop or there is a storage tank used in

conjunction with the water heater. See

Water Piping

(page 13)

and

Water Piping Diagrams

(page 39)

for

installation location of circulating pumps.

See the circulation pump wiring diagrams (

Figure 9

and

Figure 10

) for electrical hookup information. Install

in accordance with the current edition of the

National

Electrical Code, NFPA 70

or the

Canadian Electrical Code,

CSA C22.1

All bronze or stainless steel circulating pumps are

recommended for use with commercial water heaters.

Some circulating pumps are manufactured with sealed

bearings and do not require further lubrication. Some

circulating pumps must be periodically oiled. Refer to

the pump manufacturer’s instructions for lubrication

requirements.

CIRCULATING PUMP WIRING DIAGRAM

STORAGE TANK OR BUILDING RECIRCULATION

FIELD SUPPLIED TEMPERATURE CONTROL

INSTALLED IN THE STORAGE TANK

OR CIRCULATING LOOP RETURN LINE

CIRC

PUMP

MOTOR

L1 HOT

L2 NEUTRAL

120 VAC

POWER

NOTE:

USE SEPARATE 120 VAC POWER

SUPPLY FOR PUMP CIRCUIT. DO NOT

SHARE POWER WITH APPLIANCE AS THIS

MAY CAUSE ELECTRICAL LINE NOISE AND

LEAD TO ERRATIC CONTROL SYSTEM

OPERATION.

FIGURE 9. STORAGE TANK/BUILDING RECIRCULATION

CIRCULATING PUMP WIRING DIAGRAM

DISHWASHER LOOP WITH TOGGLE SWITCH

FIELD SUPPLIED TEMPERATURE

CONTROL INSTALLED IN THE

CIRCULATING LOOP RETURN LINE

DISHWASHER

TOGGLE

SWITCH

CIRC

PUMP

MOTOR

L1 HOT

L2 NEUTRAL

120 VAC

POWER

NOTE:

USE SEPARATE 120 VAC POWER

SUPPLY FOR PUMP CIRCUIT. DO NOT

SHARE POWER WITH APPLIANCE AS THIS

MAY CAUSE ELECTRICAL LINE NOISE AND

LEAD TO ERRATIC CONTROL SYSTEM

OPERATION.

FIGURE 10. DISHWASHER LOOP WITH TOGGLE SWITCH

Содержание BT-100-LP
















































Результаты поиска

Содержание BT-100-LP

Отзывы:

Похожие инструкции для BT-100-LP

Бренды по названию

Популярные бренды

A.O. Smith BT-100-LP, Инструкция по эксплуатации

Результаты поиска

Содержание BT-100-LP

Отзывы:

Похожие инструкции для BT-100-LP

Бренды по названию

Популярные бренды