A.O. Smith AWH-35 Скачать руководство пользователя страница 5

5

GROUNDING INSTRUCTIONS

This heat pump water heater must be grounded in accordance 

with the National Electrical Code and/or local codes. These must 

be  followed  in  all  cases.  Failure  to  ground  this  water  heater 

properly may also cause erratic control system operation. 
This heat pump water heater must be connected to a grounded 

metal,  permanent  wiring  system;  or  an  equipment  grounding 

conductor must be run with the circuit conductors and connected 

to the equipment grounding terminal or lead on the water heater.

GENERAL SAFETY INFORMATION

PRECAUTIONS

DO  NOT  USE  THIS  APPLIANCE  IF  ANY  PART  HAS  BEEN 

UNDER WATER. Immediately call a qualified service agency to 

inspect the appliance and to make a determination on what steps 

should be taken next.
If  the  unit  is  exposed  to  the  following,  do  not  operate  heater 

until all corrective steps have been made by a qualified service 

agency.
1.  External fire.
2.  Damage.
3.

   Running

 without water.

When servicing this unit, verify the power to the unit is turned off prior to opening the control cabinet door.

CONTAINS REFRIGERANT! 

System contains oil and refrigerant under high pressure. Recover 

refrigerant to relieve pressure before opening the system. See unit 

rating label for refrigerant type. Do not use non-approved refrigerants, 

refrigerant substitutes, or refrigerant additives.
Failure to follow proper procedures or the use of non-approved 

refrigerants, refrigerant substitutes, or refrigerant additives could 

result in death or serious injury or equipment damage. 

Explosion Hazard

Do not use oxygen to purge or

pressurize system for leak test.

Oxygen reacts violently with oil,

which can cause an explosion

resulting in severe personal 

injury or death.

Turn off power to the water heater

before performing any service.

Electrical Shock Hazard

Label all wires prior to disconnecting

when performing service. Wiring errors

can cause improper and dangerous

operation.

Verify proper operation after servicing.

Failure to follow these instructions can

result in personal injury or death.

Water temperature over 125°F (52°C)

can cause severe burns instantly

resulting in severe injury or death.
Children, the elderly and the

physically or mentally disabled are at

highest risk for scald injury.
Feel water before bathing or

showering.
Temperature limiting devices such as

mixing valves must be installed

when required by codes and to

ensure safe temperatures at fixtures.

Read and understand this instruction

manual and the safety messages

herein before installing, operating or

servicing this water heater.
Failure to follow these instructions and

safety messages could result in death

or serious injury.
This manual must remain with the

water heater.

Explosion Hazard

Overheated water can cause

water tank explosion.

Properly sized temperature and

pressure relief valve must be

installed in the opening provided

on connected storage tanks.

Содержание AWH-35

















































Отзывы: